Hello again! As Mr. Marvin adviced to me, I got a newer kernel, version 2.6.16; and I got slmodem and ungrab-winmodem version 20070505. I loaded the ungrab-winmodem module, and this was the output: device 1057:3052 is grabbed by driver serial: try to release ACPI: PCI interrupt for device 0000:00:09.0 disabled just like Mr. Alvaro said. Then I loaded "slamr debug=3", and this was the output: slamr: module license 'Smart Link Ltd.' taints kernel. slamr: SmartLink AMRMO modem. slamr: probe 1057:3052 SL1900 card... ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 16 <p354.945288> amrmo_card_create: data c4bfc000. <p354.945296> tAmrMo::tAmrMo: card c4bfc000, pci cdd75800, irq 16. <p354.945303> HWDriver: StartTable Phys = 47ED000, Lin = C47ED000, IO 10 <p354.945310> HWDriver: StartTable Phys = 47EB000, Lin = C47EB000, IO 0 <p354.945318> HWDriver: SIL3052Card::SIL3052Card() <p354.945324> HWDriver: PageIn : linear C47A8000, physical 47A8000 <p354.945330> HWDriver: PageOut: linear C47A0000, physical 47A0000 <p354.945338> amr_create: cc1cec00 (amrmo c4bfc000) <p354.945374> amrmo_card_enable: card c4d54300. <p354.945382> [Hardware instance constructor...] <p354.945388> HWDriver: SIL3052Card::ModemOpen() <p354.945396> checkLock Vid=1057 <p354.945400> HWDriver: SIL3052Card::InitHw() <p354.945405> InitHW <p354.945413> HWDriver: ModemBaseIO=C000 <p354.945417> HWDriver: SIL3052Card::ValidatePCIConfiguration() <p354.945424> Additional delay 0 <p354.945428> Delay reduction of 0 <p354.945434> HWDriver: PCI core reset the DAA ... <p354.995183> HWDriver: SIL3052_CHIPSET_REV_C detected. Assume using 32.768KHz Osc. <p355.170410> SIL3052codec: Setting for Automatic Calibration mode... <p355.170420> HWDriver: SIL3052codec::Initialize end of Initialize reg status <p355.170426> 3052CodecDump:>>>> Reg 28 = 3000000 <p355.170432> 3052CodecDump:>>>> Reg 33 = 0 <p355.170438> 3052CodecDump:>>>> Reg 34 = 0 <p355.170443> 3052CodecDump:>>>> Reg 35 = 0 <p355.170449> 3052CodecDump:>>>> Reg 3c = 0 ; LCS MB(4:0) <p355.170455> 3052CodecDump:>>>> Reg 40 = 8 ; DCT MB(3:2) <p355.170461> 3052CodecDump:>>>> Reg 41 = 0 ; CALD MB(5) MCAL MB(6) CALZ MB(7) <p355.170467> 3052CodecDump:>>>> Reg 49 = 8 ;(RCALD MB(5) <p355.170473> 3052CodecDump:>>>> Reg 4f = 20 ; FOH MB(6:5) <p355.170479> HWDriver: SIL3052codec::SetSampleRateHz =9600 <p355.170492> HWDriver: SIL3052codec::SetupForRing() enter <p355.170500> HWDriver: SIL3052codec::SetupForRing() exit <p355.170505> 3052CodecDump:>>>> Reg 28 = 3000000 <p355.170511> 3052CodecDump:>>>> Reg 33 = 0 <p355.170517> 3052CodecDump:>>>> Reg 34 = 20 <p355.170523> 3052CodecDump:>>>> Reg 35 = 0 <p355.170528> 3052CodecDump:>>>> Reg 3c = 0 ; LCS MB(4:0) <p355.170534> 3052CodecDump:>>>> Reg 40 = 8 ; DCT MB(3:2) <p355.170540> 3052CodecDump:>>>> Reg 41 = 0 ; CALD MB(5) MCAL MB(6) CALZ MB(7) <p355.170546> 3052CodecDump:>>>> Reg 49 = 0 ;(RCALD MB(5) <p355.170552> 3052CodecDump:>>>> Reg 4f = 20 ; FOH MB(6:5) <p355.260180> SIL3052 Error:2 InitHW() fail because DAA Frame not detected <p355.260189> MC details: Si3018 Int-DAA(@) <p355.260194> Chipset: Si3052(D) <p355.260201> checkLock Vid=1057 <p355.260207> HWDriver: ModemOpen() dwResult2= 4112;bFrameDetectERROR=1(ModemHelperTestResult=2) <p355.260213> HWDriver: SIL3052Card::ModemOpen() - Error in modem open function <p355.260219> hal: cannot open modem card. <p355.260224> Construction failure! <p355.260228> Predefined rates: in 9600, out 9600 <p355.260234> OnHardwareInstanceDestroyed <p355.260238> HWDriver: SIL3052Card::ModemClose() <p355.260243> HWDriver: SIL3052Card::StopWatchdogTimer() <p355.260252> HWDriver: SIL3052DMAChannel::Reset() <p355.260259> HWDriver: SIL3052DMAChannel::Reset() <p355.260266> DeInitHW slamr: cannot init card. <p355.260281> amrmo_card_delete: card c4d54300. <p355.260287> amr_delete: cc1cec00... ACPI: PCI interrupt for device 0000:00:09.0 disabled So, it doesn`t work yet. On boot, the kernel detects the modem, like this: ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 16 0000:00:09.0: ttyS1 at I/O 0xc008 (irq = 16) is a 16450 0000:00:09.0: ttyS2 at I/O 0xc010 (irq = 16) is a 8250 0000:00:09.0: ttyS3 at I/O 0xc018 (irq = 16) is a 16450 Couldn't register serial port 0000:00:09.0: -28 Maybe there is the problem... I use the distro Mandriva GNU/Linux 2006, but I will try with Debian, and see if it works. Thanks again! Hugo S. Cardozo --- Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> escribió: > Hugo, > > As Alvaro reports below > ungrab-winmodem is working with a 2.6.15 kernel. > > Perhaps you can upgrade to a kernel more current > than 2.6.12-12mdk-150407 > > MarvS > > ---------- Forwarded message ---------- > From: Alvaro Aguirre <alvaro.aguirre@xxxxxxxxx> > Date: May 31, 2007 2:30 PM > Subject: Re: Problem with Motorola SM56 / Smartlink > SL? > To: Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> > > > I reinstall the modem in other computer with Ubuntu > Dapper (kernel > 2.6.15-23-server) It's working flawless using > ungrab-winmodem and > slamr. > Ungrab-winmodem and slamr are 20070505 version > > When ungrab-winmodem works ok you would expect this > message: > May 31 13:23:28 atreides kernel: [42949382.410000] > device 1057:3052 is > grabbed by driver serial: try to release > May 31 13:23:28 atreides kernel: [42949382.410000] > ACPI: PCI interrupt > for device 0000:03:0d.0 disabled > > Alvaro > __________________________________________________ Correo Yahoo! Espacio para todos tus mensajes, antivirus y antispam ¡gratis! Regístrate ya - http://correo.espanol.yahoo.com/
