Hi Marvin, First - really appreciate the efforts your all make to get these nasty modems to work on linux. Any way am still suffering with win modems and other compatible stuff This is the result of trying wvdialconf /etc/wvdial.conf ram@ram:~$ sudo wvdialconf /etc/wvdial.conf Password: Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. Modem Port Scan<*1>: S0 S1 S2 S3 S4 S5 S6 S7 Modem Port Scan<*1>: S8 S9 S10 S11 S12 S13 S14 S15 Modem Port Scan<*1>: S16 S17 S18 S19 S20 S21 S22 S23 Modem Port Scan<*1>: S24 S25 S26 S27 S28 S29 S30 S31 Modem Port Scan<*1>: S32 S33 S34 S35 S36 S37 S38 S39 Modem Port Scan<*1>: S40 S41 S42 S43 S44 S45 S46 S47 WvModem<*1>: Cannot get information for serial port. ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>. ** What Next ??? Will try the regular winmodem as well - the reason I want to set this serial to usb stuff is because the phone it connects to is partly mobile (IFWT) allowing me the advantage of limited mobility. Thanks and regards ram Marvin Stodolsky wrote: > Ram, > > The >> > http://phep2.technion.ac.il/linmodems/packages/hsfhda/ >> > and also read Smartlink.txt and use The >> > hsfmodem-7.47.00.03ful_patched.tar.gz > should work for you. The intial speed will be a slow 14.4 mH for testing. > To enable the full 56 mH you have to pay www.linuxant.com for a software > key > > It is not clean whether >> >> [17179585.756000] drivers/usb/serial/usb-serial.c: USB Serial support >> >> registered for pl2303 >> >> [17179585.756000] pl2303 3-1:1.0: pl2303 converter detected >> >> [17179585.756000] usb 3-1: pl2303 converter now attached to ttyUSB0 >> >> [17179585.756000] usbcore: registered new driver pl2303 >> >> [17179585.756000] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to >> >> serial adaptor driver > represents a successful setup of the USB modem. But just try: > $ sudo wvdialconf /etc/wvdial.conf > The modem will be detected and tested if the setup is OK, and > /etc/wvdial.conf will be written > > You can edit in your personal information between the < > symbols, using > $ sudo gedit /etc/wvdial.conf > Do remove the < > symbols, and add a line > Carrier Check = no > and save. > > Then try a dialout with > $ sudo wvdial > > MarvS > > > > > > On 1/19/07, ramnarayan.k@xxxxxxxxx <ramnarayan.k@xxxxxxxxx> wrote: >> >> Hi Marvin, >> Sorry for this long delay in between mails >> >> A few queries >> First the SGS Thomson Microelectonics is the finger print reader so this >> is not a modem (silly but asking anyway) >> >> Second the serial-to-usb modem is : >> Bus 003 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial >> Port >> >> So are the instructions given for this >> >> *or* >> Are you saying that the winmodem aboard the laptop is compatible and i >> have to download the packages in >> > http://phep2.technion.ac.il/linmodems/packages/hsfhda/ >> > and also read Smartlink.txt and use The >> > hsfmodem-7.47.00.03ful_patched.tar.gz >> >> and if i follow the instructions my winmodem should work. >> >> seeking your kind clarification >> >> thanks >> and regards >> ram >> >> >> >> >> Marvin Stodolsky wrote: >> > Ram >> > >> > 0483:2016 SGS Thomson Microelectronics USB modem >> > is supported by the slmodem software plus slusb.ko driver. For your >> > Ubuntu 2.6.15-27-686 kernel, I'll send you a driver package >> > separately. >> > However we have never had a test under the intermediate serial-to-usb >> > driver. >> > >> > You can also get service from: >> > Class 0403: 8086:27d8 0403: Intel Corporation 82801G >> > Primary PCI_id 8086:27d8 >> > Subsystem PCI_id 17aa:2010 >> > Softmodem codec or Vendor from diagnostics: 14f1, a Conexant type. >> > from Archives: 14f1, a Conexant type. >> > >> > First install the packages: linux-headers-2.6.15-27 and >> > linux-headers-2.6.15-27-686 which can be found through >> > Under Linux they can be installed with: >> > $ sudo dpkg -i linux*.deb >> > >> > Then download the packages in >> > http://phep2.technion.ac.il/linmodems/packages/hsfhda/ >> > and also read Smartlink.txt . The >> > hsfmodem-7.47.00.03ful_patched.tar.gz can be unpacked with: >> > $ tar zxf hsfmodem*.tar.gz >> > Read instructions therein. >> > >> > MarvS >> > scanModem maintainer >> > >> > On 11/29/06, Ramnarayan. K <ramnarayan.k@xxxxxxxxx> wrote >> >> Hi >> >> >> >> Am asking for help with a serial to usb connected modem >> >> >> >> some details are below >> >> >> >> regards >> >> ram >> >> >> >> ran scanmodem but got no output that related to this but am posting >> >> that as an attachment in case it helps (anyway) >> >> >> >> ram@ram-t60:~$ lsusb >> >> Bus 005 Device 001: ID 0000:0000 >> >> Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics >> >> Fingerprint ReaderBus 004 Device 001: ID 0000:0000 >> >> Bus 002 Device 001: ID 0000:0000 >> >> Bus 003 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 >> >> Serial Port >> >> Bus 003 Device 001: ID 0000:0000 >> >> Bus 001 Device 001: ID 0000:0000 >> >> >> >> >> >> >> >> dmesg output after connecting usb fixed wireless telephone >> >> >> >> [17179574.524000] usbcore: registered new driver usbfs >> >> [17179574.524000] usbcore: registered new driver hub >> >> [17179574.528000] USB Universal Host Controller Interface driver v2.3 >> >> >> >> >> >> [17179575.172000] kjournald starting. Commit interval 5 seconds >> >> [17179575.844000] usb 3-1: new full speed USB device using uhci_hcd >> >> and address 2 >> >> [17179576.220000] usb 4-2: new full speed USB device using uhci_hcd >> >> and address 2 >> >> >> >> >> >> >> >> [17179585.732000] usbcore: registered new driver usbserial >> >> [17179585.732000] drivers/usb/serial/usb-serial.c: USB Serial support >> >> registered for generic >> >> [17179585.736000] usbcore: registered new driver usbserial_generic >> >> [17179585.736000] drivers/usb/serial/usb-serial.c: USB Serial >> Driver core >> >> >> >> >> >> [17179585.756000] drivers/usb/serial/usb-serial.c: USB Serial support >> >> registered for pl2303 >> >> [17179585.756000] pl2303 3-1:1.0: pl2303 converter detected >> >> [17179585.756000] usb 3-1: pl2303 converter now attached to ttyUSB0 >> >> [17179585.756000] usbcore: registered new driver pl2303 >> >> [17179585.756000] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to >> >> serial adaptor driver >> >> >> >> >> >> >> > >> >> >> >
