Ralf, I have submitted a Bug Report with your and related info, includingJoerns comments on the streaming issue to discuss@xxxxxxxxxxxxx MarvS On 1/20/07, Ralf Hambach <Seppel817325@xxxxxx> wrote:> Thanks for the comments at first.>> I think, I'm running in the same problems as Lajos> (Vendor Id: 0x11c11040) and my intention to post is> only to contribute additional data (as asked for in> ModemData.txt)>> Currently I have recompiled versions of> *alsa 1.0.14rc2 (driver, lib,..., compiled for> hda_intel + debugging, exactly following the> ALSA documentation for snd_hda_intel)> *slmodem-2.9.11-20061021>> a soft-modem is detected on the sound-card, wvdialconf runs> and gives again:> Modem = /dev/ttySL0> Init1 = ATZ> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0> Init3 = AT+MS=34> Modem Type = Analog Modem> ISDN = 0> New PPPD = yes> Baud = 460800> Carrier Check = no>> but I get the same output as before when I start wvdial> - no carrier and dmesg prints:>> ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1400 invalid rate 9600> ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:1153: hda-intel: invalid format_val, rate=9600, ch=1, format=2> ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627 hda_codec_setup_sream: NID=0x1, stream=0x0, channel=0, format=0x0>> Ralf.>> >> > Acting as root> > # wvdialconf /etc/wvdial.conf> > creates /etc/wvdial.conf . A typical one after editing is like:> >> > [Dialer Defaults]> > Modem = /dev/ttySL0> > Init1 = ATZ> > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0> > Modem Type = Analog Modem> > Phone = DialUpNumber> > ISDN = 0> > Username = LoginName> > Password = YourPassWord> > Baud = 460800> > # needs for /dev/ptsN ports> > Carrier Check = no> > ## End> >> > But for the Vendor Id: 0x11c11040 modems, there likely will still be> > problems, As Lajos has reported.> >> > As mentioned earlier. It is work a try to also do an ALSA lib update from> > the> > alsa-lib-1.0.14rc2 folded. Read the instructions therein.> > Also compile a new slmodemd which will use the newly installed libs.> >> > >From http://phep2.technion.ac.il/linmodems/packages/smartlink/> > get the slmodem-2.9.11-20061021.tar.gz Under Linux> > $ tar zxf slmodem-2.9.11-20061021.tar.gz> > $ cd slmodem-2.9.11-20061021> > Look around with> > $ ls> >> > To make and ALSA competent slmodemd:> > $ cd modem> > $ ls> > $ make clean> > $ make ALSA=1> > $ ls -l slmodemd> > should display the product. Then replace the old one.> > $ su - root> > # sudo cp slmodemd /usr/sbin/slmodemd> > Best reboot and test a dialout> >> > MarvS> >> >> >> >> >> >> >> >> > On 1/20/07, Jacques Goldberg <Jacques.Goldberg@xxxxxxx> wrote:> > > Ralf,> > > When wvdial shows this:> > > --> Cannot get information for serial port.> > > there is no point continuing.> > > The error> > > > NO CARRIER> > > > ERROR> > > > --> No Carrier!> > > is not an error at all: there just is no modem known to wvdial, and what> > > wvdial sent out, the dial command for example, fall down in a black> > hole.> > >> > > Please forgive me for quoting from experience that the most frequent> > > cause is that the user has not yet created a correct /etc/wvdial.conf> > > configuration file using the program wvdialconf> > >> > > Jacques>>> --> Der GMX SmartSurfer hilft bis zu 70% Ihrer Onlinekosten zu sparen!> Ideal für Modem und ISDN: http://www.gmx.net/de/go/smartsurfer>
