Thanks for the comments at first. I think, I'm running in the same problems as Lajos (Vendor Id: 0x11c11040) and my intention to post is only to contribute additional data (as asked for in ModemData.txt) Currently I have recompiled versions of *alsa 1.0.14rc2 (driver, lib,..., compiled for hda_intel + debugging, exactly following the ALSA documentation for snd_hda_intel) *slmodem-2.9.11-20061021 a soft-modem is detected on the sound-card, wvdialconf runs and gives again: Modem = /dev/ttySL0 Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Init3 = AT+MS=34 Modem Type = Analog Modem ISDN = 0 New PPPD = yes Baud = 460800 Carrier Check = no but I get the same output as before when I start wvdial - no carrier and dmesg prints: ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1400 invalid rate 9600 ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:1153: hda-intel: invalid format_val, rate=9600, ch=1, format=2 ALSA /usr/src/alsa/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627 hda_codec_setup_sream: NID=0x1, stream=0x0, channel=0, format=0x0 Ralf. > > Acting as root > # wvdialconf /etc/wvdial.conf > creates /etc/wvdial.conf . A typical one after editing is like: > > [Dialer Defaults] > Modem = /dev/ttySL0 > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > Modem Type = Analog Modem > Phone = DialUpNumber > ISDN = 0 > Username = LoginName > Password = YourPassWord > Baud = 460800 > # needs for /dev/ptsN ports > Carrier Check = no > ## End > > But for the Vendor Id: 0x11c11040 modems, there likely will still be > problems, As Lajos has reported. > > As mentioned earlier. It is work a try to also do an ALSA lib update from > the > alsa-lib-1.0.14rc2 folded. Read the instructions therein. > Also compile a new slmodemd which will use the newly installed libs. > > >From http://phep2.technion.ac.il/linmodems/packages/smartlink/ > get the slmodem-2.9.11-20061021.tar.gz Under Linux > $ tar zxf slmodem-2.9.11-20061021.tar.gz > $ cd slmodem-2.9.11-20061021 > Look around with > $ ls > > To make and ALSA competent slmodemd: > $ cd modem > $ ls > $ make clean > $ make ALSA=1 > $ ls -l slmodemd > should display the product. Then replace the old one. > $ su - root > # sudo cp slmodemd /usr/sbin/slmodemd > Best reboot and test a dialout > > MarvS > > > > > > > > > On 1/20/07, Jacques Goldberg <Jacques.Goldberg@xxxxxxx> wrote: > > Ralf, > > When wvdial shows this: > > --> Cannot get information for serial port. > > there is no point continuing. > > The error > > > NO CARRIER > > > ERROR > > > --> No Carrier! > > is not an error at all: there just is no modem known to wvdial, and what > > wvdial sent out, the dial command for example, fall down in a black > hole. > > > > Please forgive me for quoting from experience that the most frequent > > cause is that the user has not yet created a correct /etc/wvdial.conf > > configuration file using the program wvdialconf > > > > Jacques -- Der GMX SmartSurfer hilft bis zu 70% Ihrer Onlinekosten zu sparen! Ideal für Modem und ISDN: http://www.gmx.net/de/go/smartsurfer
