On 7/15/2015 12:05 PM, Jindal, Sonika wrote:
On 7/14/2015 7:52 PM, Imre Deak wrote:
On ti, 2015-07-14 at 11:18 +0530, Sonika Jindal wrote:
As per bspec, on BXT A0/A1, sw needs to activate DDIA HPD logic
and interrupts to check the external panel connection and DDIC HPD
logic for edp panel.
Signed-off-by: Sonika Jindal <sonika.jindal@xxxxxxxxx>
---
drivers/gpu/drm/i915/intel_dp.c | 18 ++++++++++++++++--
drivers/gpu/drm/i915/intel_hdmi.c | 9 ++++++++-
2 files changed, 24 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 7b54b9d..c32f3d3 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -5869,10 +5869,24 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,
/* Set up the hotplug pin. */
switch (port) {
case PORT_A:
- intel_encoder->hpd_pin = HPD_PORT_A;
+ /*
+ * On BXT A0/A1, sw needs to activate DDIC HPD logic and
+ * interrupts to check the eDP panel connection.
+ */
+ if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
+ intel_encoder->hpd_pin = HPD_PORT_C;
+ else
+ intel_encoder->hpd_pin = HPD_PORT_A;
break;
case PORT_B:
- intel_encoder->hpd_pin = HPD_PORT_B;
+ /*
+ * On BXT A0/A1, sw needs to activate DDIA HPD logic and
+ * interrupts to check the external panel connection.
+ */
+ if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
+ intel_encoder->hpd_pin = HPD_PORT_A;
+ else
+ intel_encoder->hpd_pin = HPD_PORT_B;
break;
case PORT_C:
intel_encoder->hpd_pin = HPD_PORT_C;
This won't work for a couple of reasons: atm i915_digport_work_func()
assumes a fixed pin->port mapping, for example it'll call the HPD
handler for the port A encoder for a short/long pulse event triggered
via the HPD_PORT_A pin, whereas after the above patch you want to select
port B's encoder on BXT A0/1. This could be fixed by setting up
hotplug.irq_port in intel_ddi_init() according to the above change, or
not using irq_port at all, but instead looking up the encoder the same
way i915_hotplug_work_func() does using intel_encoder->hpd_pin.
Hmm, i didnt realize that.
Moving this check to intel_ddi_init, will again make the checks spread
all over which we wanted to avoid since hpd_pin was in place.
But looks like hpd_pin is only for i915_hotplug_work_func.
I feel we can move back to the older approach itself
What do you suggest?
But then we can remove these checks from here, and have it only in
intel_ddi_init, right? So it should look fine.
For HPD_PORT_A, I think we can skip that part as of now.
Please suggest..
Daniel, any comments?
The HPD_PORT_A HPD handling is missing in general, see
for_each_hpd_pin() and intel_hpd_irq_handler()/is_dig_port.
So if going with the above way, these issues need to be addressed first.
--Imre
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
