From: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
The docs are a bit lacking when it comes to describing when certain
timing related events occur in the hardware. Draw a picture which
tries to capture the most important ones.
v2: Clarify a few details (Imre)
Acked-by: Imre Deak <imre.deak@xxxxxxxxx>
Signed-off-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
---
drivers/gpu/drm/i915/i915_irq.c | 49 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 742f276..bc4585b 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -669,6 +669,55 @@ i915_pipe_enabled(struct drm_device *dev, int pipe)
}
}
+/*
+ * This timing diagram depicts the video signal in and
+ * around the vertical blanking period.
+ *
+ * Assumptions about the fictitious mode used in this example:
+ * vblank_start >= 3
+ * vsync_start = vblank_start + 1
+ * vsync_end = vblank_start + 2
+ * vtotal = vblank_start + 3
+ *
+ * start of vblank:
+ * latch double buffered registers
+ * increment frame counter (ctg+)
+ * generate start of vblank interrupt (gen4+)
+ * |
+ * | frame start:
+ * | generate frame start interrupt (aka. vblank interrupt) (gmch)
+ * | may be shifted forward 1-3 extra lines via PIPECONF
+ * | |
+ * | | start of vsync:
+ * | | generate vsync interrupt
+ * | | |
+ * ___xxxx___ ___xxxx___ ___xxxx___ ___xxxx___ ___xxxx___ ___
+ * . \hs/ . \hs/ \hs/ \hs/ . \hs/
+ * ----va---> <-----------------vb--------------------> <--------va---------
+ * | | <----vs-----> |
+ * -vbs-----> <---vbs+1---> <---vbs+2---> <-----0-----> <-----1-----> <---2- (scanline counter gen2)
+ * -vbs-2---> <---vbs-1---> <---vbs-----> <---vbs+1---> <---vbs+2---> <---0- (scanline counter gen3+)
+ * | | |
+ * last visible pixel first visible pixel
+ * | increment frame counter (gen3/4)
+ * pixel counter = vblank_start * htotal pixel counter = 0 (gen3/4)
+ *
+ * x = horizontal active
+ * _ = horizontal blanking
+ * hs = horizontal sync
+ * va = vertical active
+ * vb = vertical blanking
+ * vs = vertical sync
+ * vbs = vblank_start (number)
+ *
+ * Summary:
+ * - most events happen at the start of horizontal sync
+ * - frame start happens at the start of horizontal blank, 1-4 lines
+ * (depending on PIPECONF settings) after the start of vblank
+ * - gen3/4 pixel and frame counter are synchronized with the start
+ * of horizontal active on the first line of vertical active
+ */
+
static u32 i8xx_get_vblank_counter(struct drm_device *dev, int pipe)
{
/* Gen2 doesn't have a hardware frame counter */
--
1.8.3.2
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
