Quoting Mika Kuoppala (2018-01-22 15:08:16)
> Daniele Ceraolo Spurio <daniele.ceraolospurio@xxxxxxxxx> writes:
>
> > On 19/01/18 05:05, Mika Kuoppala wrote:
> >> Daniele Ceraolo Spurio <daniele.ceraolospurio@xxxxxxxxx> writes:
> >>
> >>> From: Thomas Daniel <thomas.daniel@xxxxxxxxx>
> >>>
> >>> Enhanced Execlists is an upgraded version of execlists which supports
> >>> up to 8 ports. The lrcs to be submitted are written to a submit queue,
> >>> which is then loaded on the HW. When writing to the ELSP register, the
> >>> lrcs are written cyclically in the queue from position 0 to position 7.
> >>> Alternatively, it is possible to write directly in the individual
> >>> positions of the queue using the ELSQ registers. To be able to re-use
> >>> all the existing code we're using the latter method and we're currently
> >>> limiting ourself to only using 2 elements.
> >>>
> >>> The preemption flow is sligthly different with enhanced execlists, so
> >>> this patch turns preemption off temporarily for Gen11+ while we wait for
> >>> the new mechanism to land.
> >>>
> >>> v2: Rebase.
> >>> v3: Switch from !IS_GEN11 to GEN < 11 (Daniele Ceraolo Spurio).
> >>> v4: Use the elsq registers instead of elsp. (Daniele Ceraolo Spurio)
> >>> v5: Reword commit, rename regs to be closer to specs, turn off
> >>> preemption (Daniele), reuse engine->execlists.elsp (Chris)
> >>>
> >>> Cc: Chris Wilson <chris@xxxxxxxxxxxxxxxxxx>
> >>> Signed-off-by: Thomas Daniel <thomas.daniel@xxxxxxxxx>
> >>> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@xxxxxxxxx>
> >>> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@xxxxxxxxx>
> >>
> >> Was going to adopt this patch from Rodrigo but you were faster.
> >>
> >> I choose to stash the elsq and use it as a gen11 vs rest toggle:
> >>
> >> Relevant bits:
> >>
> >> +static inline void write_port(struct intel_engine_execlists * const execlists,
> >> + unsigned int n,
> >> + u64 desc)
> >> +{
> >> + if (execlists->elsq)
> >> + gen11_elsq_write(desc, n, execlists->elsq);
> >> + else
> >> + gen8_elsp_write(desc, execlists->elsp);
> >> +}
> >> +
> >> +static inline void submit_ports(struct intel_engine_execlists * const execlists)
> >> +{
> >> + /* for gen11+ we need to manually load the submit queue */
> >> + if (execlists->elsq) {
> >> + struct intel_engine_cs *engine =
> >> + container_of(execlists,
> >> + struct intel_engine_cs,
> >> + execlists);
> >> + struct drm_i915_private *dev_priv = engine->i915;
> >> +
> >> + I915_WRITE_FW(RING_ELCR(engine), ELCR_LOAD);
> >> + }
> >> +}
> >> +
> >>
> >
> > I was undecided about hiding the code in sub-functions because of the
> > pre-emption path. There is no need in gen11 to inject a context to
> > preempt to idle,
Really? The preempt-to-idle is so that we can sync the bookkeeping with
the pending CS interrupts. The HW doesn't require it currently either,
it's the SW that does. If you have a way to avoid that, that should be
applicable to the current code as well?
-Chris
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
