Dear Michal, Thank you for your email. What I have seen is, when a rule is added, it does not, for some reason, apply to calls already running that falls under that rule. Only new calls are processed. In my case, I found the new rule to be working alright the next day, without any changes, and any reboot of GnuGK. So, I guess, CapacityControl starts tracking calls once a rule becomes available. Regards HASSAAN ----- Original Message ----- From: "Zygmuntowicz Michal" <m.zygmuntowicz@xxxxxxx> To: <openh323gk-users@xxxxxxxxxxxxxxxxxxxxx> Sent: Tuesday, May 16, 2006 22:55 Subject: Re: Capacity Control in GnuGK 2.2.4 > I'd recommend setting debug trc 6 and reloading the config. In the debug log > you will see whether capacity control entries are correctly loaded and > current/max > call volumes for each rule. Maybe the rules are not loaded correctly. > > ----- Original Message ----- > From: "Nyamul Hassaan" <mnhassan@xxxxxxx> > Sent: Sunday, May 14, 2006 8:45 PM > > > I finally got hold of Visual Studio .NET 2003 (7.1) and successfully > compiled GnuGK 2.2.4, using Mimas Patch 2 versions of OpenH323 and PWLib. > The compiling went smooth, and was feeling like tearing my hair off for not > trying this path earlier! :) > > The new version is up and running in my production server for the last 24 > hours, without any problems so far. I've got capacity control enabled, and > have one customer restricted to 45 channels on a particular route. I used > the following settings for this customer: > > %r1% ip:a.b.c.d=120 > %r2% ip:a.b.c.d=^(88017) 45 > > Later in the day, I wanted to restrict another customer to two routes and > had the following settings: > > %r4% ip:m.n.o.0/24=^(8802) 8 > %r3% ip:m.n.o.0/24=^(88017) 16 > > These do not seem to be working. The customer was doing 15 + 3 calls on > 8802 and 23 + 7 on 88017, and after adding those settings, I didn't see any > change. > > My capacity control related ini settings are: > > [Gatekeeper::Auth] > CapacityControl=required;Setup > FileIPAuth=required;GRQ,RRQ,LRQ,Setup > > [Gatekeeper::Acct] > CapacityControl=required;start,stop > FileAcct=sufficient;stop > > [CapacityControl] > %r1% ip:a.b.c.d=120 > %r2% ip:a.b.c.d=^(88017) 45 > %r4% ip:m.n.o.0/24=^(8802) 8 > %r3% ip:m.n.o.0/24=^(88017) 16 > > I've read the manual over again, and as far as I can make out of it, this is > how it is supposed to be. But, I could've missed something, so suggestions > would be greatly appreciated. > > With warm regards > HASSAAN > > > P.S.: The 2nd example for Capacity Control of the online manual reads > "[RewriteCLI]" as the section header. Is that correct? Or should it read > "[CapacityControl]" as the 1st example? > > > > ------------------------------------------------------- > Using Tomcat but need to do more? Need to support web services, security? > Get stuff done quickly with pre-integrated technology to make your job easier > Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > _______________________________________________________ > > Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx > Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 > Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users > Homepage: http://www.gnugk.org/ > ------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 _______________________________________________________ Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users Homepage: http://www.gnugk.org/
