Re: using a preferred node ?

[Ravishankar N <ravishankar@xxxxxxxxxx>]

On 06/08/2015 11:34 AM, Mathieu Chateau wrote:

Hello Ravi,

thanks for clearing things up.

Anything on the roadmap that would help my case?

I don't think it would be possible for clients to do I/O only on its local brick and yet expect the bricks' contents to be in sync in real-time..

Cordialement,
Mathieu CHATEAU
http://www.lotp.fr

2015-06-08 6:37 GMT+02:00 Ravishankar N <ravishankar@xxxxxxxxxx>:

On 06/06/2015 12:49 AM, Mathieu Chateau wrote:

Hello,

sorry to bother again but I am still facing this issue.

client still looks on the "other side" and not using the node declared in fstab:

prd-sta-sto01:/gluster-preprod /mnt/gluster-preprod glusterfs defaults,_netdev,backupvolfile-server=prd-sta-sto02 0 0

I expect client to use sto01 and not sto02 as it's available.

Hi Mathieu,
When you do lookups (`ls` etc), they are sent to both bricks of the replica. If you write to a file, the write is also sent to both bricks. This is how it works. Only reads are served from the local brick.
-Ravi

If I add a static route to break connectivity to sto02 and do a "df", I have around 30s before it works.

Then it works ok.

Questions:

• How to force node to stick as possible with one specific (local) node ?
• How to know where a client is currently connected?

Thanks for your help :)

Cordialement,
Mathieu CHATEAU
http://www.lotp.fr

2015-05-11 7:26 GMT+02:00 Mathieu Chateau <mathieu.chateau@xxxxxxx>:

Hello,

thanks for helping :)

If gluster server is rebooted, any way to make client failback on node after reboot ?

How to know which node is using a client ? I see TCP connection to both node 

Regards,

Cordialement,
Mathieu CHATEAU
http://www.lotp.fr

2015-05-11 7:13 GMT+02:00 Ravishankar N <ravishankar@xxxxxxxxxx>:

On 05/10/2015 08:29 PM, Mathieu Chateau wrote:

Hello,

Short way: Is there any way to define a preferred Gluster server ?

Long way:

I have the following setup (version 3.6.3) :

Gluster A  <==> VPN <==> Gluster B

Volume is replicated between A and B.

They are in same datacenter, using a 1Gb/s connection, low latency (0.5ms)

I have gluster clients in lan A & B.

When doing a "ls" on big folder (~60k files), both gluster node are used, and so it need 9mn instead on 1mn if only the local gluster is reachable.

Lookups (and writes of course) from clients are sent to both  bricks because AFR uses the result of the lookup to select which brick to read from if there is a pending heal etc.
If the file is clean on both A and B, then reads are always served from the local brick. i.e. reads on clients mounted on A will be served from the brick in A (and likewise for B).

Hope that helps,
Ravi

It's HA setup, application is present on both side. I would like a master/master setup, but using only local node as possible.

Regards,
Mathieu CHATEAU
http://www.lotp.fr

_______________________________________________
Gluster-users mailing list
Gluster-users@xxxxxxxxxxx
http://www.gluster.org/mailman/listinfo/gluster-users

_______________________________________________
Gluster-users mailing list
Gluster-users@xxxxxxxxxxx
http://www.gluster.org/mailman/listinfo/gluster-users