2008/8/31 Antonio M <antonio.montagnani@xxxxxxxxx>:
> 2008/8/30 Antonio Olivares <olivares14031@xxxxxxxxx>:
>>
>>
>>
>> --- On Sat, 8/30/08, Antonio M <antonio.montagnani@xxxxxxxxx> wrote:
>>
>>> From: Antonio M <antonio.montagnani@xxxxxxxxx>
>>> Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot
>>> To: "For testers of Fedora Core development releases" <fedora-test-list@xxxxxxxxxx>
>>> Date: Saturday, August 30, 2008, 7:03 AM
>>> 2008/8/29 Andrew Gormanly <a.gormanly@xxxxxxxxx>:
>>> > More output, the battery failed before I could
>>> transcribe the top couple of
>>> > pages though.
>>> >
>>> > Andrew Gormanly wrote:
>>> >>
>>> >> Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does
>>> not boot but
>>> >> 2.6.27-0.244.rc4.git1.fc10.i686 is ok
>>> >>
>>> >> Without rhgb but with quiet the messages are:
>>> >>
>>> >> stabilized: stat /proc/bus/usb/devices: No such
>>> file or directory
>>> >> mount: error mounting /dev/root on /sysroot as
>>> ext3: No such file or
>>> >> directory
>>> >> setuproot: moving /dev failed: No such file or
>>> directory
>>> >> setuproot: error mounting /proc: No such file or
>>> directory
>>> >> setuproot: error mounting /sys: No such file or
>>> directory
>>> >> Mount failed for selinuxfs on /selinux: No such
>>> file or directory
>>> >> switchroot: mount failed: No such file or
>>> directory
>>> >> sd 0:0:0:0: [sda] Assuming drive cache: write
>>> through
>>> >> sd 0:0:0:0: [sda] Assuming drive cache: write
>>> through
>>> >>
>>> >> I'll copy out the full messages from the
>>> kernel and post when I have them.
>>> >> This will take ages though.
>>> >>
>>> >> Hardware is an Asus Eee PC 4G with rawhide
>>> installed on an 8GB SDHC card
>>> >> in the built-in reader. Fedora 9 kernels were ok
>>> as was
>>> >> 2.6.27-0.244.rc4.git1.fc10
>>> >>
>>> >
>>> >
>>> > --
>>> > Andrew Gormanly
>>> > London Centre for Nanotechnology
>>> > University College London
>>> Tel: 020 7679 3400
>>> > 17-19 Gordon Street
>>> Fax: 020 7679 0595
>>> > London WC1H 0AJ
>>> a.gormanly AT ucl.ac.uk
>>> >
>>> > pci 0000:00:1c.1: IO window: disabled
>>> > pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff
>>> > pci 0000:00:1c.1: PREFETCH window: disabled
>>> > pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01
>>> > pci 0000:00:1c.2: IO window: disabled
>>> > pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff
>>> > pci 0000:00:1c.2: PREFETCH window:
>>> 0x000000f0000000-0x000000f6ffffff
>>> > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
>>> > pci 0000:00:1e.0: IO window: disabled
>>> > pci 0000:00:1e.0: MEM window: disabled
>>> > pci 0000:00:1e.0: PREFETCH window: disabled
>>> > pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low)
>>> -> IRQ 16
>>> > pci 0000:00:1c.0: setting latency timer to 64
>>> > pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low)
>>> -> IRQ 17
>>> > pci 0000:00:1c.1: setting latency timer to 64
>>> > pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low)
>>> -> IRQ 18
>>> > pci 0000:00:1c.2: setting latency timer to 64
>>> > pci 0000:00:1e.0: setting latency timer to 64
>>> > bus: 00 index 0 io port: [0, ffff]
>>> > bus: 00 index 1 mmio: [0, ffffffffffffffff]
>>> > bus: 04 index 0 mmio: [0, 0]
>>> > bus: 04 index 1 mmio: [0, 0]
>>> > bus: 04 index 2 mmio: [0, 0]
>>> > bus: 04 index 3 mmio: [0, 0]
>>> > bus: 03 index 0 mmio: [0, 0]
>>> > bus: 03 index 1 mmio: [fbf00000, fbffffff]
>>> > bus: 03 index 2 mmio: [0, 0]
>>> > bus: 03 index 3 mmio: [0, 0]
>>> > bus: 01 index 0 mmio: [0, 0]
>>> > bus: 01 index 1 mmio: [f8000000, fbefffff]
>>> > bus: 01 index 2 mmio: [f0000000, f6ffffff]
>>> > bus: 01 index 3 mmio: [0, 0]
>>> > bus: 05 index 0 mmio: [0, 0]
>>> > bus: 05 index 1 mmio: [0, 0]
>>> > bus: 05 index 2 mmio: [0, 0]
>>> > bus: 05 index 3 io port: [0, ffff]
>>> > bus: 05 index 4 mmio: [0, ffffffffffffffff]
>>> > NET: Registered protocol family 2
>>> > IP route cache hash table entries: 32768 (order: 5,
>>> 131072 bytes)
>>> > TCP established has table entriesL 131072 (order: 8,
>>> 1048576 bytes)
>>> > TCP bind hash table entriesL 65536 (order: 9, 2359296
>>> bytes)
>>> > TCP: Hash tables configured (established 131072 bind
>>> 65536)
>>> > TCP reno registered
>>> > NET: Registered protocol family 1
>>> > checking if image is initramfs... it is
>>> > Switched to high resolution on CPU 0
>>> > debug: unmapping init memory f7d5e000..f7ff0000
>>> > apm: BIOS version 1.2 Flags 0x03 (Driver version
>>> 1.16ac)
>>> > apm: overridden by ACPI
>>> > audit: initializing netlink socket (disabled)
>>> > type=2000 audit(1220021774.217:1): initialized
>>> > highmem bounce pool size: 64 pages
>>> > HugeTLB registered 4 MB page size, pre-allocated 0
>>> pages
>>> > VFS: Disk quotas dquot_6.5.1
>>> > Dquot-cache hash table entries: 1024 (order 0, 4096
>>> bytes)
>>> > msgmni has been set to 1704
>>> > SELinux: Registering netfilter hooks
>>> > Block layer SCSI generic (bsg) driver version 0.4
>>> loaded (major 252)
>>> > io scheduler noop registered
>>> > io scheduler anticipatory registered
>>> > io scheduler deadline registered
>>> > io scheduler cfg registered (default)
>>> > pci 0000:00:02.0: Boot video device
>>> > pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup =
>>> 0x0f30
>>> > pci 0000:00:1d.0: Performing full reset
>>> > pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup =
>>> 0x0030
>>> > pci 0000:00:1d.1: Performing full reset
>>> > pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup =
>>> 0x0030
>>> > pci 0000:00:1d.2: Performing full reset
>>> > pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup =
>>> 0x0030
>>> > pci 0000:00:1d.3: Performing full reset
>>> > pcieport-driver 0000:00:1c.0: setting latency timer to
>>> 64
>>> > pcieport-driver 0000:00:1c.0: found MSI capability
>>> > pci_express 0000:00:1c.0:pcie00: allocate port service
>>> > pci_express 0000:00:1c.0:pcie02: allocate port service
>>> > pci_express 0000:00:1c.0:pcie03: allocate port service
>>> > pcieport-driver 0000:00:1c.1: setting latency timer to
>>> 64
>>> > pcieport-driver 0000:00:1c.1: found MSI capability
>>> > pci_express 0000:00:1c.1:pcie00: allocate port service
>>> > pci_express 0000:00:1c.1:pcie02: allocate port service
>>> > pci_express 0000:00:1c.1:pcie03: allocate port service
>>> > pcieport-driver 0000:00:1c.2: setting latency timer to
>>> 64
>>> > pcieport-driver 0000:00:1c.2: found MSI capability
>>> > pci_express 0000:00:1c.2:pcie00: allocate port service
>>> > pci_express 0000:00:1c.2:pcie02:allocate port service
>>> > pci_express 0000:00:1c.2:pcie03:allocate port service
>>> > pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>>> > input: Power Button (FF) as
>>> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
>>> > ACPI: Power Button (FF) [PWRF]
>>> > input: Lid Switch as
>>> /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
>>> > ACPI: EC: non-query interrupt received, switching to
>>> interrupt mode
>>> > ACPI: Lid Switch [LID]
>>> > input: Sleep Buttion (CM) as
>>> > /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2
>>> > ACPI: Sleep Button (CM) [SLPB]
>>> > input: Power Button (CM) as
>>> > /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
>>> > ACPI: Power Button (CM) [PWRB]
>>> > ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3])
>>> > processor ACPI0007:00: registered as cooling_device0
>>> > ACPI: Processor [CPU1] (supports 8 throttling states)
>>> > thermal LNXTHERM:01: registered as thermal_zone0
>>> > ACPI: Thermal Zone [TZ00] (35 C)
>>> > isapnp: Scanning for PnP cards...
>>> > isapnp: No Plug & Play device found
>>> > Non-volatile memory driver v1.2
>>> > Linux agpgart interface v0.103
>>> > agpgart-intel 0000:00:00.0: Intel 915GM Chipset
>>> > agpgart-intel 0000:00:00.0: detected 7932K stolen
>>> memory
>>> > agpgart-intel 0000:00:00.0: AGP aperture is 256M @
>>> 0xd0000000
>>> > Serial: 8250/16550 driver4 ports, IRQ sharing enabled
>>> > brd: module loaded
>>> > input: Macintosh mouse button emulation as
>>> /devices/virtual/input/input4
>>> > Driver 'sd' needs updating - please use
>>> bus_type methods
>>> > ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
>>> > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level,
>>> low) -> IRQ 23
>>> > ehci_hcd 0000:00:1d.7: setting latency timer to 64
>>> > ehci_hcd 0000:00:1d.7: EHCI Host Controller
>>> > drivers/usb/core/inode.c: creating file
>>> 'devices'
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > ehci_hcd 0000:00:1d.7: new USB bus registered,
>>> assigned bus number 1
>>> > ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
>>> cc=4 pcc=2 ordered
>>> > !ppc ports=8
>>> > ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
>>> uframes 1024 64 bit
>>> > addr
>>> > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
>>> ithresh=8 period=1024
>>> > Reset HALT
>>> > ehci_hcd 0000:00:1d.7: debug port 1
>>> > ehci_hcd 0000:00:1d.7: cache line size of 32 is not
>>> supported
>>> > ehci_hcd 0000:00:1d.7: supports USB remote wakeup
>>> > ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00
>>> > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
>>> ithresh=8 period=1024
>>> > Reset HALT
>>> > ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
>>> ithresh=1 period-1024
>>> > RUN
>>> > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
>>> driver 10 Dec 2004
>>> > usb usb1: default language 0x409
>>> > usb usb1: uevent
>>> > usb usb1: usb_probe_device
>>> > usb usb1: configuration #1 chosen from 1 choice
>>> > usb usb1: adding 1-0:1.0 (config #1, interface 0)
>>> > usb 1-0:1.0: uevent
>>> > hub 1-0:1.0: usb_probe_interface
>>> > hub 1-0:1.0: usb_probe_interface - got id
>>> > hub 1-0:1.0: USB hub found
>>> > hub 1-0:1.0: 8 ports detected
>>> > hub 1-0:1.0: standalone hub
>>> > hub 1-0:1.0: no power switching (usb 1.0)
>>> > hub 1-0:1.0: individual port over-current protection
>>> > hub 1-0:1.0: power on to power good time: 20ms
>>> > hub 1-0:1.0: local power source is good
>>> > hub 1-0:1.0: trying to enable port power on
>>> non-switchable hub
>>> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803
>>> POWER sig=j CSC
>>> > CONNECT
>>> > hub 1-0:1.0: port 5: status 0501 change 0001
>>> > hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > hub 1-0:1.0: port 5, status 0501, change 0000, 480
>>> Mb/s
>>> > usb usb1: New USB device found, idVendor=1d6b,
>>> idProduct=0002
>>> > usb usb1: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> > usb usb1: Product: EHCI Host Controller
>>> > usb usb1: Manufacturer: Linux
>>> 2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd
>>> > usb usb1: SerialNumber: 0000:00:1d.7
>>> > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host
>>> Controller (OHCI) Driver
>>> > ohci_hcd: block sizes: ed 64 td 64
>>> > USB Universal Host Controller Interface driver v3.0
>>> > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level,
>>> low) -> IRQ 23
>>> > uhci_hcd 0000:00:1d.0: setting latency timer to 64
>>> > uhci_hcd 0000:00:1d.0: UHCI Host Controller
>>> > drivers/usb/core/inode.c: creating file '002'
>>> > uhci_hcd 0000:00:1d.0: new USB bus registered,
>>> assigned bus number 2
>>> > uhci_hcd 0000:00:1d.0: detected 2 ports
>>> > uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd =
>>> 0x0000
>>> > uhci_hcd 0000:00:1d.0: Performing full reset
>>> > uhci_hcd 0000:00:1d.0: supports USB remote wakeup
>>> > uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400
>>> > usb usb3: default language 0x409
>>> > usb usb3: uevent
>>> > usb usb3: usb_probe_device
>>> > usb usb3: configuration #1 chosen from 1 choice
>>> > usb usb3: adding 2-0:1.0 (config #1, interface 0)
>>> > usb 2-0:1.0: uevent
>>> > hub 2-0:1.0: usb_probe_interface
>>> > hub 2-0:1.0: usb_probe_interface - got id
>>> > hub 2-0:1.0: USB hub found
>>> > hub 2-0:1.0: 2 ports detected
>>> > hub 2-0:1.0: standalone hub
>>> > hub 2-0:1.0: no power switching (usb 1.0)
>>> > hub 2-0:1.0: individual port over-current protection
>>> > hub 2-0:1.0: power on to power good time: 2ms
>>> > hub 2-0:1.0: local power source is good
>>> > hub 2-0:1.0: trying to enable port power on
>>> non-switchable hub
>>> > ehci_hcd 0000:00:1d.7: port 5 high speed
>>> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
>>> POWER sig=se0 PE
>>> > CONNECT
>>> > usb 1-5: new high speed USB device using ehci_hcd and
>>> address 2
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > usb usb2: New USB device found, idVendor=1d6b,
>>> idProduct=0001
>>> > usb usb2: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> > usb usb2: Product: UHCI Host Controller
>>> > usb usb2: Manufacturer: Linux
>>> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
>>> > usb usb2: SerialNumber: 0000:00:1d.0
>>> > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level,
>>> low) -> IRQ 19
>>> > uhci_hcd 0000:00:1d.1: setting latency timer to 64
>>> > uhci_hcd 0000:00:1d.1: UHCI Host Controller
>>> > drivers/usb/core/inode.c: creating file '003'
>>> > uhci_hcd 0000:00:1d.1: new USB bus registered,
>>> assigned bus number 3
>>> > uhci_hcd 0000:00:1d.1: detected 2 ports
>>> > uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd =
>>> 0x0000
>>> > uhci_hcd 0000:00:1d.1: Performing full reset
>>> > uhci_hcd 0000:00:1d.1: supports USB remote wakeup
>>> > uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480
>>> > usb usb3: default language 0x409
>>> > usb usb3: uevent
>>> > usb usb3: usb_probe_device
>>> > usb usb3: configuration #1 chosen from 1 choice
>>> > usb usb3: adding 3-0:1.0 (config #1, interface 0)
>>> > usb 3-0:1.0: uevent
>>> > hub 3-0:1.0: usb_probe_interface
>>> > hub 3-0:1.0: usb_probe_interface - got id
>>> > hub 3-0:1.0: USB hub found
>>> > hub 3-0:1.0: 2 ports detected
>>> > hub 3-0:1.0: standalone hub
>>> > hub 3-0:1.0: no power switching (usb 1.0)
>>> > hub 3-0:1.0: individual port over-current protection
>>> > hub 3-0:1.0: power on to power good time: 2ms
>>> > hub 3-0:1.0: local power source is good
>>> > hub 3-0:1.0: trying to enable port power on
>>> non-switchable hub
>>> > ehci_hcd 0000:00:1d.7: port 5 high speed
>>> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
>>> POWER sig=se0 PE
>>> > CONNECT
>>> > usb 1-5: default language 0x0409
>>> > usb 1-5: uevent
>>> > usb 1-5: usb_probe_device
>>> > usb 1-5: configuration #1 chosen from 1 choice
>>> > usb 1-5: adding 1-5:1.0 (config #1, interface 0)
>>> > usb 1-5:1.0: uevent
>>> > drivers/usb/core/inode.c: creating file '002'
>>> > usb 1-5: New USB device found, idVendor=0951,
>>> idProduct=1606
>>> > usb 1-5: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=4
>>> > usb 1-5: Product: UB6225
>>> > usb 1-5: Manufacturer: ENE
>>> > usb 1-5: SerialNumber: 146030377350
>>> > hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
>>> > hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > usb usb3: New USB device found, idVendor=1d6b,
>>> idProduct=0001
>>> > usb usb3: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> > usb usb3: Product: UHCI Host Controller
>>> > usb usb3: Manufacturer: Linux
>>> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
>>> > usb usb3: SerialNumber: 0000:00:1d.1
>>> > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level,
>>> low) -> IRQ 18
>>> > uhci_hcd 0000:00:1d.2: setting latency timer to 64
>>> > uhci_hcd 0000:00:1d.2: UHCI Host Controller
>>> > drivers/usb/core/inode.c: creating file '004'
>>> > uhci_hcd 0000:00:1d.2: new USB bus registered,
>>> assigned bus number 4
>>> > uhci_hcd 0000:00:1d.2: detected 2 ports
>>> > uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd =
>>> 0x0000
>>> > uhci_hcd 0000:00:1d.2: Performing full reset
>>> > uhci_hcd 0000:00:1d.2: supports USB remote wakeup
>>> > uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
>>> > usb usb4: default language 0x409
>>> > usb usb4: uevent
>>> > usb usb4: usb_probe_device
>>> > usb usb4: configuration #1 chosen from 1 choice
>>> > usb usb4: adding 4-0:1.0 (config #1, interface 0)
>>> > usb 4-0:1.0: uevent
>>> > usb 4-0:1.0: usb_probe_interface
>>> > usb 4-0:1.0: usb_probe_interface - got id
>>> > usb 4-0:1.0: USB hub found
>>> > usb 4-0:1.0: 2 ports detected
>>> > usb 4-0:1.0: standalone hub
>>> > usb 4-0:1.0: no power switching (usb 1.0)
>>> > usb 4-0:1.0: individual port over-current protection
>>> > usb 4-0:1.0: power on to power good time: 2ms
>>> > usb 4-0:1.0: local power source is good
>>> > usb 4-0:1.0: trying to enable port power on
>>> non-switchable hub
>>> > uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00
>>> > usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > usb usb4: New USB device found, idVendor=1d6b,
>>> idProduct=0001
>>> > usb usb4: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> > usb usb4: Product: UHCI Host Controller
>>> > usb usb4: Manufacturer: Linux
>>> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
>>> > usb usb4: SerialNumber: 0000:00:1d.2
>>> > uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level,
>>> low) -> IRQ 16
>>> > uhci_hcd 0000:00:1d.3: setting latency timer to 64
>>> > uhci_hcd 0000:00:1d.3: UHCI Host Controller
>>> > drivers/usb/core/inode.c: creating file '005'
>>> > uhci_hcd 0000:00:1d.3: new USB bus registered,
>>> assigned bus number 5
>>> > uhci_hcd 0000:00:1d.3: detected 2 ports
>>> > uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd =
>>> 0x0000
>>> > uhci_hcd 0000:00:1d.3: Performing full reset
>>> > uhci_hcd 0000:00:1d.3: supports USB remote wakeup
>>> > uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880
>>> > usb usb5: default language 0x409
>>> > usb usb5: uevent
>>> > usb usb5: usb_probe_device
>>> > usb usb5: configuration #1 chosen from 1 choice
>>> > usb usb5: adding 5-0:1.0 (config #1, interface 0)
>>> > usb 5-0:1.0: uevent
>>> > usb 5-0:1.0: usb_probe_interface
>>> > usb 5-0:1.0: usb_probe_interface - got id
>>> > usb 5-0:1.0: USB hub found
>>> > usb 5-0:1.0: 2 ports detected
>>> > hub 5-0:1.0: standalone hub
>>> > hub 5-0:1.0: no power switching (usb 1.0)
>>> > hub 5-0:1.0: individual port over-current protection
>>> > hub 5-0:1.0: power on to power good time: 2ms
>>> > hub 5-0:1.0: local power source is good
>>> > hub 5-0:1.0: trying to enable port power on
>>> non-switchable hub
>>> > hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
>>> > drivers/usb/core/inode.c: creating file '001'
>>> > usb usb5: New USB device found, idVendor=1d6b,
>>> idProduct=0001
>>> > usb usb5: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> > usb usb5: Product: UHCI Host Controller
>>> > usb usb5: Manufacturer: Linux
>>> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
>>> > usb usb5: SerialNumber: 0000:00:1d.3
>>> > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
>>> 0x60,0x64 irq 1,12
>>> > serio: i8042 KBD port at 0x60,0x64 irq 1
>>> > Setting up hotplug.rt at 0x60,0x64 irq 12
>>> > Creating block device nodes.on for all mice
>>> > Loading ext3 module core: registered rtc_cmos as rtc0
>>> > usb usb2: suspend_rh (auto-stop)et irqs
>>> > usb usb3: suspend_rh (auto-stop)
>>> > Loading usb-storage modulenu
>>> > Initializing USB Mass Storage driver...r hiddev
>>> > usb-storage 1-5:1.0: usb_probe_interface usbhid
>>> > usb-storage 1-5:1.0: usb_probe_interface - got id
>>> > scsi0 : SCSI emulation for USB Mass Storage devices
>>> > usbcore: registered new interface driver usb-storage
>>> > USB Mass Storage support registered.
>>> > Waiting for driver initialization.
>>> > stabilized: stat /proc/bus/usb/devices: No such file
>>> or directory
>>> > Creating root device. :941
>>> > usb-storage: device found at 207f9000..c096d000
>>> > usb-storage: waiting for device to settle before
>>> scaning
>>> > Mounting root filesystem.2 keyboard as
>>> > /devices/platform/i8042/serio/input/inpu
>>> > mount: error mounting /dev/root on /sysroot as ext3:
>>> No such file or
>>> > directory
>>> > Setting up other filesystems.
>>> > setuproot: moving /dev failed: No such file or
>>> directory
>>> > setuproot: error mounting /proc: No such file or
>>> directory
>>> > setuproot: error mounting /sys: No such file or
>>> directory
>>> > Mount failed for selinuxfs on /selinux: No such file
>>> or directory
>>> > Switching to new root and running init.
>>> > switchroot: mount failed: No such file or directory
>>> > Booting has failed.
>>> > usb usb4: suspend_rh (auto-stop)
>>> > Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1,
>>> caps: 0xa04751/0xa00000
>>> > input: SynPS/2 Synaptics TouchPad as
>>> > /devices/platform/i8042/serio1/input/input6
>>> > usb usb5: suspend_rh (auto-stop)
>>> > hub 2-0:1.0: hub_suspend
>>> > usb usb2: bus auto-suspend
>>> > usb usb2: suspend_rh
>>> > hub 3-0:1.0: hub_suspend
>>> > usb usb3: bus auto-suspend
>>> > usb usb3: suspend_rh
>>> > hub 4-0:1.0: hub_suspend
>>> > usb usb4: bus auto-suspend
>>> > usb usb4: suspend_rh
>>> > hub 5-0:1.0: hub_suspend
>>> > usb usb5: bus auto-suspend
>>> > usb usb5: suspend_rh
>>> > usb-storage: device scan complete
>>> > scsi 0:0:0:0: Direct-Access USB2.0 CardReader
>>> SD0 0100 PQ: 0 ANSI: 0
>>> > sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors
>>> (8169 MB)
>>> > sd 0:0:0:0: [sda] Write Protect is off
>>> > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
>>> > sd 0:0:0:0: Assuming drive cache: write through
>>> > sd 0:0:0:0: 15954944 512-byte hardware sectors (8169
>>> MB)
>>> > sd 0:0:0:0: [sda] Write Protect is off
>>> > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
>>> > sd 0:0:0:0: Assuming drive cache: write through
>>> > sda: sda1 sda2
>>> > sd 0:0:0:0: [sda] Attached SCSI removable disk
>>> > sd 0:0:0:0: Attached SCSI generic sg0 type 0
>>> > scsi_scan_0 used greatest stack depth: 1928 bytes left
>>> >
>>> > --
>>> > fedora-test-list mailing list
>>> > fedora-test-list@xxxxxxxxxx
>>> > To unsubscribe:
>>> >
>>> https://www.redhat.com/mailman/listinfo/fedora-test-list
>>> >
>>> also 287 has exactly same problem.....that means that
>>> nobody read
>>> this thread :-( and I spent some time to install and
>>> de-install the
>>> kernel.
>> It happens at some point or another. I installed the 284 kernel and it worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :)
>>
>> BTW, thank you for bringing up the printing problem. I am having problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :(
>>>
>>>
>>> --
>>> Antonio Montagnani
>>> Skype : antoniomontag
>>>
>>> --
>>
>> Regards,
>>
>> Antonio
>>
>>
>>
>>
>>
>> --
>> fedora-test-list mailing list
>> fedora-test-list@xxxxxxxxxx
>> To unsubscribe:
>> https://www.redhat.com/mailman/listinfo/fedora-test-list
>>
>
> even kernel-2.6.27-0.290.rc5.fc10.i686 is not booting off my USB HD
> drive, with same problems of other two kernels.
> Latest kernel booting off an USB HD drive is
> kernel-2.6.27-0.244.rc2.git1.fc10.i686.
>
>
> --
> Antonio Montagnani
> Skype : antoniomontag
>
filed a bug: Bug 460762 - Recent kernels don't boot off USB devices
Please add your comments
--
Antonio Montagnani
Skype : antoniomontag
-- fedora-test-list mailing list fedora-test-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
