--- On Sat, 8/30/08, Antonio M <antonio.montagnani@xxxxxxxxx> wrote: > From: Antonio M <antonio.montagnani@xxxxxxxxx> > Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot > To: "For testers of Fedora Core development releases" <fedora-test-list@xxxxxxxxxx> > Date: Saturday, August 30, 2008, 7:03 AM > 2008/8/29 Andrew Gormanly <a.gormanly@xxxxxxxxx>: > > More output, the battery failed before I could > transcribe the top couple of > > pages though. > > > > Andrew Gormanly wrote: > >> > >> Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does > not boot but > >> 2.6.27-0.244.rc4.git1.fc10.i686 is ok > >> > >> Without rhgb but with quiet the messages are: > >> > >> stabilized: stat /proc/bus/usb/devices: No such > file or directory > >> mount: error mounting /dev/root on /sysroot as > ext3: No such file or > >> directory > >> setuproot: moving /dev failed: No such file or > directory > >> setuproot: error mounting /proc: No such file or > directory > >> setuproot: error mounting /sys: No such file or > directory > >> Mount failed for selinuxfs on /selinux: No such > file or directory > >> switchroot: mount failed: No such file or > directory > >> sd 0:0:0:0: [sda] Assuming drive cache: write > through > >> sd 0:0:0:0: [sda] Assuming drive cache: write > through > >> > >> I'll copy out the full messages from the > kernel and post when I have them. > >> This will take ages though. > >> > >> Hardware is an Asus Eee PC 4G with rawhide > installed on an 8GB SDHC card > >> in the built-in reader. Fedora 9 kernels were ok > as was > >> 2.6.27-0.244.rc4.git1.fc10 > >> > > > > > > -- > > Andrew Gormanly > > London Centre for Nanotechnology > > University College London > Tel: 020 7679 3400 > > 17-19 Gordon Street > Fax: 020 7679 0595 > > London WC1H 0AJ > a.gormanly AT ucl.ac.uk > > > > pci 0000:00:1c.1: IO window: disabled > > pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff > > pci 0000:00:1c.1: PREFETCH window: disabled > > pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01 > > pci 0000:00:1c.2: IO window: disabled > > pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff > > pci 0000:00:1c.2: PREFETCH window: > 0x000000f0000000-0x000000f6ffffff > > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 > > pci 0000:00:1e.0: IO window: disabled > > pci 0000:00:1e.0: MEM window: disabled > > pci 0000:00:1e.0: PREFETCH window: disabled > > pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) > -> IRQ 16 > > pci 0000:00:1c.0: setting latency timer to 64 > > pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) > -> IRQ 17 > > pci 0000:00:1c.1: setting latency timer to 64 > > pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) > -> IRQ 18 > > pci 0000:00:1c.2: setting latency timer to 64 > > pci 0000:00:1e.0: setting latency timer to 64 > > bus: 00 index 0 io port: [0, ffff] > > bus: 00 index 1 mmio: [0, ffffffffffffffff] > > bus: 04 index 0 mmio: [0, 0] > > bus: 04 index 1 mmio: [0, 0] > > bus: 04 index 2 mmio: [0, 0] > > bus: 04 index 3 mmio: [0, 0] > > bus: 03 index 0 mmio: [0, 0] > > bus: 03 index 1 mmio: [fbf00000, fbffffff] > > bus: 03 index 2 mmio: [0, 0] > > bus: 03 index 3 mmio: [0, 0] > > bus: 01 index 0 mmio: [0, 0] > > bus: 01 index 1 mmio: [f8000000, fbefffff] > > bus: 01 index 2 mmio: [f0000000, f6ffffff] > > bus: 01 index 3 mmio: [0, 0] > > bus: 05 index 0 mmio: [0, 0] > > bus: 05 index 1 mmio: [0, 0] > > bus: 05 index 2 mmio: [0, 0] > > bus: 05 index 3 io port: [0, ffff] > > bus: 05 index 4 mmio: [0, ffffffffffffffff] > > NET: Registered protocol family 2 > > IP route cache hash table entries: 32768 (order: 5, > 131072 bytes) > > TCP established has table entriesL 131072 (order: 8, > 1048576 bytes) > > TCP bind hash table entriesL 65536 (order: 9, 2359296 > bytes) > > TCP: Hash tables configured (established 131072 bind > 65536) > > TCP reno registered > > NET: Registered protocol family 1 > > checking if image is initramfs... it is > > Switched to high resolution on CPU 0 > > debug: unmapping init memory f7d5e000..f7ff0000 > > apm: BIOS version 1.2 Flags 0x03 (Driver version > 1.16ac) > > apm: overridden by ACPI > > audit: initializing netlink socket (disabled) > > type=2000 audit(1220021774.217:1): initialized > > highmem bounce pool size: 64 pages > > HugeTLB registered 4 MB page size, pre-allocated 0 > pages > > VFS: Disk quotas dquot_6.5.1 > > Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) > > msgmni has been set to 1704 > > SELinux: Registering netfilter hooks > > Block layer SCSI generic (bsg) driver version 0.4 > loaded (major 252) > > io scheduler noop registered > > io scheduler anticipatory registered > > io scheduler deadline registered > > io scheduler cfg registered (default) > > pci 0000:00:02.0: Boot video device > > pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = > 0x0f30 > > pci 0000:00:1d.0: Performing full reset > > pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = > 0x0030 > > pci 0000:00:1d.1: Performing full reset > > pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = > 0x0030 > > pci 0000:00:1d.2: Performing full reset > > pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = > 0x0030 > > pci 0000:00:1d.3: Performing full reset > > pcieport-driver 0000:00:1c.0: setting latency timer to > 64 > > pcieport-driver 0000:00:1c.0: found MSI capability > > pci_express 0000:00:1c.0:pcie00: allocate port service > > pci_express 0000:00:1c.0:pcie02: allocate port service > > pci_express 0000:00:1c.0:pcie03: allocate port service > > pcieport-driver 0000:00:1c.1: setting latency timer to > 64 > > pcieport-driver 0000:00:1c.1: found MSI capability > > pci_express 0000:00:1c.1:pcie00: allocate port service > > pci_express 0000:00:1c.1:pcie02: allocate port service > > pci_express 0000:00:1c.1:pcie03: allocate port service > > pcieport-driver 0000:00:1c.2: setting latency timer to > 64 > > pcieport-driver 0000:00:1c.2: found MSI capability > > pci_express 0000:00:1c.2:pcie00: allocate port service > > pci_express 0000:00:1c.2:pcie02:allocate port service > > pci_express 0000:00:1c.2:pcie03:allocate port service > > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > > input: Power Button (FF) as > /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 > > ACPI: Power Button (FF) [PWRF] > > input: Lid Switch as > /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 > > ACPI: EC: non-query interrupt received, switching to > interrupt mode > > ACPI: Lid Switch [LID] > > input: Sleep Buttion (CM) as > > /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2 > > ACPI: Sleep Button (CM) [SLPB] > > input: Power Button (CM) as > > /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 > > ACPI: Power Button (CM) [PWRB] > > ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3]) > > processor ACPI0007:00: registered as cooling_device0 > > ACPI: Processor [CPU1] (supports 8 throttling states) > > thermal LNXTHERM:01: registered as thermal_zone0 > > ACPI: Thermal Zone [TZ00] (35 C) > > isapnp: Scanning for PnP cards... > > isapnp: No Plug & Play device found > > Non-volatile memory driver v1.2 > > Linux agpgart interface v0.103 > > agpgart-intel 0000:00:00.0: Intel 915GM Chipset > > agpgart-intel 0000:00:00.0: detected 7932K stolen > memory > > agpgart-intel 0000:00:00.0: AGP aperture is 256M @ > 0xd0000000 > > Serial: 8250/16550 driver4 ports, IRQ sharing enabled > > brd: module loaded > > input: Macintosh mouse button emulation as > /devices/virtual/input/input4 > > Driver 'sd' needs updating - please use > bus_type methods > > ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 > > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, > low) -> IRQ 23 > > ehci_hcd 0000:00:1d.7: setting latency timer to 64 > > ehci_hcd 0000:00:1d.7: EHCI Host Controller > > drivers/usb/core/inode.c: creating file > 'devices' > > drivers/usb/core/inode.c: creating file '001' > > ehci_hcd 0000:00:1d.7: new USB bus registered, > assigned bus number 1 > > ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 > cc=4 pcc=2 ordered > > !ppc ports=8 > > ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 > uframes 1024 64 bit > > addr > > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 > ithresh=8 period=1024 > > Reset HALT > > ehci_hcd 0000:00:1d.7: debug port 1 > > ehci_hcd 0000:00:1d.7: cache line size of 32 is not > supported > > ehci_hcd 0000:00:1d.7: supports USB remote wakeup > > ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00 > > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 > ithresh=8 period=1024 > > Reset HALT > > ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 > ithresh=1 period-1024 > > RUN > > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, > driver 10 Dec 2004 > > usb usb1: default language 0x409 > > usb usb1: uevent > > usb usb1: usb_probe_device > > usb usb1: configuration #1 chosen from 1 choice > > usb usb1: adding 1-0:1.0 (config #1, interface 0) > > usb 1-0:1.0: uevent > > hub 1-0:1.0: usb_probe_interface > > hub 1-0:1.0: usb_probe_interface - got id > > hub 1-0:1.0: USB hub found > > hub 1-0:1.0: 8 ports detected > > hub 1-0:1.0: standalone hub > > hub 1-0:1.0: no power switching (usb 1.0) > > hub 1-0:1.0: individual port over-current protection > > hub 1-0:1.0: power on to power good time: 20ms > > hub 1-0:1.0: local power source is good > > hub 1-0:1.0: trying to enable port power on > non-switchable hub > > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803 > POWER sig=j CSC > > CONNECT > > hub 1-0:1.0: port 5: status 0501 change 0001 > > hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000 > > drivers/usb/core/inode.c: creating file '001' > > hub 1-0:1.0: port 5, status 0501, change 0000, 480 > Mb/s > > usb usb1: New USB device found, idVendor=1d6b, > idProduct=0002 > > usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > > usb usb1: Product: EHCI Host Controller > > usb usb1: Manufacturer: Linux > 2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd > > usb usb1: SerialNumber: 0000:00:1d.7 > > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host > Controller (OHCI) Driver > > ohci_hcd: block sizes: ed 64 td 64 > > USB Universal Host Controller Interface driver v3.0 > > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, > low) -> IRQ 23 > > uhci_hcd 0000:00:1d.0: setting latency timer to 64 > > uhci_hcd 0000:00:1d.0: UHCI Host Controller > > drivers/usb/core/inode.c: creating file '002' > > uhci_hcd 0000:00:1d.0: new USB bus registered, > assigned bus number 2 > > uhci_hcd 0000:00:1d.0: detected 2 ports > > uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = > 0x0000 > > uhci_hcd 0000:00:1d.0: Performing full reset > > uhci_hcd 0000:00:1d.0: supports USB remote wakeup > > uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400 > > usb usb3: default language 0x409 > > usb usb3: uevent > > usb usb3: usb_probe_device > > usb usb3: configuration #1 chosen from 1 choice > > usb usb3: adding 2-0:1.0 (config #1, interface 0) > > usb 2-0:1.0: uevent > > hub 2-0:1.0: usb_probe_interface > > hub 2-0:1.0: usb_probe_interface - got id > > hub 2-0:1.0: USB hub found > > hub 2-0:1.0: 2 ports detected > > hub 2-0:1.0: standalone hub > > hub 2-0:1.0: no power switching (usb 1.0) > > hub 2-0:1.0: individual port over-current protection > > hub 2-0:1.0: power on to power good time: 2ms > > hub 2-0:1.0: local power source is good > > hub 2-0:1.0: trying to enable port power on > non-switchable hub > > ehci_hcd 0000:00:1d.7: port 5 high speed > > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 > POWER sig=se0 PE > > CONNECT > > usb 1-5: new high speed USB device using ehci_hcd and > address 2 > > drivers/usb/core/inode.c: creating file '001' > > usb usb2: New USB device found, idVendor=1d6b, > idProduct=0001 > > usb usb2: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > > usb usb2: Product: UHCI Host Controller > > usb usb2: Manufacturer: Linux > 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd > > usb usb2: SerialNumber: 0000:00:1d.0 > > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, > low) -> IRQ 19 > > uhci_hcd 0000:00:1d.1: setting latency timer to 64 > > uhci_hcd 0000:00:1d.1: UHCI Host Controller > > drivers/usb/core/inode.c: creating file '003' > > uhci_hcd 0000:00:1d.1: new USB bus registered, > assigned bus number 3 > > uhci_hcd 0000:00:1d.1: detected 2 ports > > uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = > 0x0000 > > uhci_hcd 0000:00:1d.1: Performing full reset > > uhci_hcd 0000:00:1d.1: supports USB remote wakeup > > uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480 > > usb usb3: default language 0x409 > > usb usb3: uevent > > usb usb3: usb_probe_device > > usb usb3: configuration #1 chosen from 1 choice > > usb usb3: adding 3-0:1.0 (config #1, interface 0) > > usb 3-0:1.0: uevent > > hub 3-0:1.0: usb_probe_interface > > hub 3-0:1.0: usb_probe_interface - got id > > hub 3-0:1.0: USB hub found > > hub 3-0:1.0: 2 ports detected > > hub 3-0:1.0: standalone hub > > hub 3-0:1.0: no power switching (usb 1.0) > > hub 3-0:1.0: individual port over-current protection > > hub 3-0:1.0: power on to power good time: 2ms > > hub 3-0:1.0: local power source is good > > hub 3-0:1.0: trying to enable port power on > non-switchable hub > > ehci_hcd 0000:00:1d.7: port 5 high speed > > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 > POWER sig=se0 PE > > CONNECT > > usb 1-5: default language 0x0409 > > usb 1-5: uevent > > usb 1-5: usb_probe_device > > usb 1-5: configuration #1 chosen from 1 choice > > usb 1-5: adding 1-5:1.0 (config #1, interface 0) > > usb 1-5:1.0: uevent > > drivers/usb/core/inode.c: creating file '002' > > usb 1-5: New USB device found, idVendor=0951, > idProduct=1606 > > usb 1-5: New USB device strings: Mfr=1, Product=2, > SerialNumber=4 > > usb 1-5: Product: UB6225 > > usb 1-5: Manufacturer: ENE > > usb 1-5: SerialNumber: 146030377350 > > hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > drivers/usb/core/inode.c: creating file '001' > > usb usb3: New USB device found, idVendor=1d6b, > idProduct=0001 > > usb usb3: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > > usb usb3: Product: UHCI Host Controller > > usb usb3: Manufacturer: Linux > 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd > > usb usb3: SerialNumber: 0000:00:1d.1 > > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, > low) -> IRQ 18 > > uhci_hcd 0000:00:1d.2: setting latency timer to 64 > > uhci_hcd 0000:00:1d.2: UHCI Host Controller > > drivers/usb/core/inode.c: creating file '004' > > uhci_hcd 0000:00:1d.2: new USB bus registered, > assigned bus number 4 > > uhci_hcd 0000:00:1d.2: detected 2 ports > > uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = > 0x0000 > > uhci_hcd 0000:00:1d.2: Performing full reset > > uhci_hcd 0000:00:1d.2: supports USB remote wakeup > > uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800 > > usb usb4: default language 0x409 > > usb usb4: uevent > > usb usb4: usb_probe_device > > usb usb4: configuration #1 chosen from 1 choice > > usb usb4: adding 4-0:1.0 (config #1, interface 0) > > usb 4-0:1.0: uevent > > usb 4-0:1.0: usb_probe_interface > > usb 4-0:1.0: usb_probe_interface - got id > > usb 4-0:1.0: USB hub found > > usb 4-0:1.0: 2 ports detected > > usb 4-0:1.0: standalone hub > > usb 4-0:1.0: no power switching (usb 1.0) > > usb 4-0:1.0: individual port over-current protection > > usb 4-0:1.0: power on to power good time: 2ms > > usb 4-0:1.0: local power source is good > > usb 4-0:1.0: trying to enable port power on > non-switchable hub > > uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00 > > usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > drivers/usb/core/inode.c: creating file '001' > > usb usb4: New USB device found, idVendor=1d6b, > idProduct=0001 > > usb usb4: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > > usb usb4: Product: UHCI Host Controller > > usb usb4: Manufacturer: Linux > 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd > > usb usb4: SerialNumber: 0000:00:1d.2 > > uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, > low) -> IRQ 16 > > uhci_hcd 0000:00:1d.3: setting latency timer to 64 > > uhci_hcd 0000:00:1d.3: UHCI Host Controller > > drivers/usb/core/inode.c: creating file '005' > > uhci_hcd 0000:00:1d.3: new USB bus registered, > assigned bus number 5 > > uhci_hcd 0000:00:1d.3: detected 2 ports > > uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = > 0x0000 > > uhci_hcd 0000:00:1d.3: Performing full reset > > uhci_hcd 0000:00:1d.3: supports USB remote wakeup > > uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880 > > usb usb5: default language 0x409 > > usb usb5: uevent > > usb usb5: usb_probe_device > > usb usb5: configuration #1 chosen from 1 choice > > usb usb5: adding 5-0:1.0 (config #1, interface 0) > > usb 5-0:1.0: uevent > > usb 5-0:1.0: usb_probe_interface > > usb 5-0:1.0: usb_probe_interface - got id > > usb 5-0:1.0: USB hub found > > usb 5-0:1.0: 2 ports detected > > hub 5-0:1.0: standalone hub > > hub 5-0:1.0: no power switching (usb 1.0) > > hub 5-0:1.0: individual port over-current protection > > hub 5-0:1.0: power on to power good time: 2ms > > hub 5-0:1.0: local power source is good > > hub 5-0:1.0: trying to enable port power on > non-switchable hub > > hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > drivers/usb/core/inode.c: creating file '001' > > usb usb5: New USB device found, idVendor=1d6b, > idProduct=0001 > > usb usb5: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > > usb usb5: Product: UHCI Host Controller > > usb usb5: Manufacturer: Linux > 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd > > usb usb5: SerialNumber: 0000:00:1d.3 > > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at > 0x60,0x64 irq 1,12 > > serio: i8042 KBD port at 0x60,0x64 irq 1 > > Setting up hotplug.rt at 0x60,0x64 irq 12 > > Creating block device nodes.on for all mice > > Loading ext3 module core: registered rtc_cmos as rtc0 > > usb usb2: suspend_rh (auto-stop)et irqs > > usb usb3: suspend_rh (auto-stop) > > Loading usb-storage modulenu > > Initializing USB Mass Storage driver...r hiddev > > usb-storage 1-5:1.0: usb_probe_interface usbhid > > usb-storage 1-5:1.0: usb_probe_interface - got id > > scsi0 : SCSI emulation for USB Mass Storage devices > > usbcore: registered new interface driver usb-storage > > USB Mass Storage support registered. > > Waiting for driver initialization. > > stabilized: stat /proc/bus/usb/devices: No such file > or directory > > Creating root device. :941 > > usb-storage: device found at 207f9000..c096d000 > > usb-storage: waiting for device to settle before > scaning > > Mounting root filesystem.2 keyboard as > > /devices/platform/i8042/serio/input/inpu > > mount: error mounting /dev/root on /sysroot as ext3: > No such file or > > directory > > Setting up other filesystems. > > setuproot: moving /dev failed: No such file or > directory > > setuproot: error mounting /proc: No such file or > directory > > setuproot: error mounting /sys: No such file or > directory > > Mount failed for selinuxfs on /selinux: No such file > or directory > > Switching to new root and running init. > > switchroot: mount failed: No such file or directory > > Booting has failed. > > usb usb4: suspend_rh (auto-stop) > > Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1, > caps: 0xa04751/0xa00000 > > input: SynPS/2 Synaptics TouchPad as > > /devices/platform/i8042/serio1/input/input6 > > usb usb5: suspend_rh (auto-stop) > > hub 2-0:1.0: hub_suspend > > usb usb2: bus auto-suspend > > usb usb2: suspend_rh > > hub 3-0:1.0: hub_suspend > > usb usb3: bus auto-suspend > > usb usb3: suspend_rh > > hub 4-0:1.0: hub_suspend > > usb usb4: bus auto-suspend > > usb usb4: suspend_rh > > hub 5-0:1.0: hub_suspend > > usb usb5: bus auto-suspend > > usb usb5: suspend_rh > > usb-storage: device scan complete > > scsi 0:0:0:0: Direct-Access USB2.0 CardReader > SD0 0100 PQ: 0 ANSI: 0 > > sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors > (8169 MB) > > sd 0:0:0:0: [sda] Write Protect is off > > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 > > sd 0:0:0:0: Assuming drive cache: write through > > sd 0:0:0:0: 15954944 512-byte hardware sectors (8169 > MB) > > sd 0:0:0:0: [sda] Write Protect is off > > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 > > sd 0:0:0:0: Assuming drive cache: write through > > sda: sda1 sda2 > > sd 0:0:0:0: [sda] Attached SCSI removable disk > > sd 0:0:0:0: Attached SCSI generic sg0 type 0 > > scsi_scan_0 used greatest stack depth: 1928 bytes left > > > > -- > > fedora-test-list mailing list > > fedora-test-list@xxxxxxxxxx > > To unsubscribe: > > > https://www.redhat.com/mailman/listinfo/fedora-test-list > > > also 287 has exactly same problem.....that means that > nobody read > this thread :-( and I spent some time to install and > de-install the > kernel. It happens at some point or another. I installed the 284 kernel and it worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :) BTW, thank you for bringing up the printing problem. I am having problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :( > > > -- > Antonio Montagnani > Skype : antoniomontag > > -- Regards, Antonio -- fedora-test-list mailing list fedora-test-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
