From: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
The interrupts for EDID_READY or DDC_ERROR were never enabled in this
driver, so reading EDID always timed out when chip was powered down and
interrupts were used. Fix this and remove clearing the interrupt flags,
they are cleared in POWER_DOWN mode anyhow (according to docs and my
tests).
Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/i2c/adv7511.c | 25 +++++++++++++++++--------
1 file changed, 17 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c
index 00416f23b5cb5f..85e994796d96a4 100644
--- a/drivers/gpu/drm/i2c/adv7511.c
+++ b/drivers/gpu/drm/i2c/adv7511.c
@@ -362,12 +362,19 @@ static void adv7511_power_on(struct adv7511 *adv7511)
{
adv7511->current_edid_segment = -1;
- regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
- ADV7511_INT0_EDID_READY);
- regmap_write(adv7511->regmap, ADV7511_REG_INT(1),
- ADV7511_INT1_DDC_ERROR);
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
ADV7511_POWER_POWER_DOWN, 0);
+ if (adv7511->i2c_main->irq) {
+ /*
+ * Documentation says the INT_ENABLE registers are reset in
+ * POWER_DOWN mode. My tests with a 7511w show something else
+ * but let's stick to the documentation.
+ */
+ regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
+ ADV7511_INT0_EDID_READY);
+ regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
+ ADV7511_INT1_DDC_ERROR);
+ }
/*
* Per spec it is allowed to pulse the HDP signal to indicate that the
@@ -567,12 +574,14 @@ static int adv7511_get_modes(struct drm_encoder *encoder,
/* Reading the EDID only works if the device is powered */
if (!adv7511->powered) {
- regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
- ADV7511_INT0_EDID_READY);
- regmap_write(adv7511->regmap, ADV7511_REG_INT(1),
- ADV7511_INT1_DDC_ERROR);
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
ADV7511_POWER_POWER_DOWN, 0);
+ if (adv7511->i2c_main->irq) {
+ regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
+ ADV7511_INT0_EDID_READY);
+ regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
+ ADV7511_INT1_DDC_ERROR);
+ }
adv7511->current_edid_segment = -1;
}
--
2.1.4
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
