From: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
Fix this typo, consequently used over both files :)
Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/i2c/adv7511.c | 22 +++++++++++-----------
drivers/gpu/drm/i2c/adv7511.h | 12 ++++++------
2 files changed, 17 insertions(+), 17 deletions(-)
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c
index 50a861b12346c4..c03c1ea53fd042 100644
--- a/drivers/gpu/drm/i2c/adv7511.c
+++ b/drivers/gpu/drm/i2c/adv7511.c
@@ -378,16 +378,16 @@ static void adv7511_power_on(struct adv7511 *adv7511)
}
/*
- * Per spec it is allowed to pulse the HDP signal to indicate that the
+ * Per spec it is allowed to pulse the HPD signal to indicate that the
* EDID information has changed. Some monitors do this when they wakeup
- * from standby or are enabled. When the HDP goes low the adv7511 is
+ * from standby or are enabled. When the HPD goes low the adv7511 is
* reset and the outputs are disabled which might cause the monitor to
- * go to standby again. To avoid this we ignore the HDP pin for the
+ * go to standby again. To avoid this we ignore the HPD pin for the
* first few seconds after enabling the output.
*/
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HDP_SRC_MASK,
- ADV7511_REG_POWER2_HDP_SRC_NONE);
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_NONE);
/*
* Most of the registers are reset during power down or when HPD is low.
@@ -421,9 +421,9 @@ static bool adv7511_hpd(struct adv7511 *adv7511)
if (ret < 0)
return false;
- if (irq0 & ADV7511_INT0_HDP) {
+ if (irq0 & ADV7511_INT0_HPD) {
regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
- ADV7511_INT0_HDP);
+ ADV7511_INT0_HPD);
return true;
}
@@ -446,7 +446,7 @@ static int adv7511_irq_process(struct adv7511 *adv7511)
regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
- if (irq0 & ADV7511_INT0_HDP && adv7511->encoder)
+ if (irq0 & ADV7511_INT0_HPD && adv7511->encoder)
drm_helper_hpd_irq_event(adv7511->encoder->dev);
if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
@@ -648,10 +648,10 @@ adv7511_encoder_detect(struct drm_encoder *encoder,
if (adv7511->status == connector_status_connected)
status = connector_status_disconnected;
} else {
- /* Renable HDP sensing */
+ /* Renable HPD sensing */
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HDP_SRC_MASK,
- ADV7511_REG_POWER2_HDP_SRC_BOTH);
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_BOTH);
}
adv7511->status = status;
diff --git a/drivers/gpu/drm/i2c/adv7511.h b/drivers/gpu/drm/i2c/adv7511.h
index 6599ed538426d6..38515b30cedfc8 100644
--- a/drivers/gpu/drm/i2c/adv7511.h
+++ b/drivers/gpu/drm/i2c/adv7511.h
@@ -90,7 +90,7 @@
#define ADV7511_CSC_ENABLE BIT(7)
#define ADV7511_CSC_UPDATE_MODE BIT(5)
-#define ADV7511_INT0_HDP BIT(7)
+#define ADV7511_INT0_HPD BIT(7)
#define ADV7511_INT0_VSYNC BIT(5)
#define ADV7511_INT0_AUDIO_FIFO_FULL BIT(4)
#define ADV7511_INT0_EDID_READY BIT(2)
@@ -157,11 +157,11 @@
#define ADV7511_PACKET_ENABLE_SPARE2 BIT(1)
#define ADV7511_PACKET_ENABLE_SPARE1 BIT(0)
-#define ADV7511_REG_POWER2_HDP_SRC_MASK 0xc0
-#define ADV7511_REG_POWER2_HDP_SRC_BOTH 0x00
-#define ADV7511_REG_POWER2_HDP_SRC_HDP 0x40
-#define ADV7511_REG_POWER2_HDP_SRC_CEC 0x80
-#define ADV7511_REG_POWER2_HDP_SRC_NONE 0xc0
+#define ADV7511_REG_POWER2_HPD_SRC_MASK 0xc0
+#define ADV7511_REG_POWER2_HPD_SRC_BOTH 0x00
+#define ADV7511_REG_POWER2_HPD_SRC_HPD 0x40
+#define ADV7511_REG_POWER2_HPD_SRC_CEC 0x80
+#define ADV7511_REG_POWER2_HPD_SRC_NONE 0xc0
#define ADV7511_REG_POWER2_TDMS_ENABLE BIT(4)
#define ADV7511_REG_POWER2_GATE_INPUT_CLK BIT(0)
--
2.1.4
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
