Hi Wolfram,
Thank you for the patch.
On Monday 04 January 2016 03:33:45 Wolfram Sang wrote:
> From: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
>
> The interrupts for EDID_READY or DDC_ERROR were never enabled in this
> driver, so reading EDID always timed out when chip was powered down and
> interrupts were used. Fix this and remove clearing the interrupt flags,
> they are cleared in POWER_DOWN mode anyhow (according to docs and my
> tests).
>
> Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
> ---
> drivers/gpu/drm/i2c/adv7511.c | 25 +++++++++++++++++--------
> 1 file changed, 17 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c
> index 00416f23b5cb5f..85e994796d96a4 100644
> --- a/drivers/gpu/drm/i2c/adv7511.c
> +++ b/drivers/gpu/drm/i2c/adv7511.c
> @@ -362,12 +362,19 @@ static void adv7511_power_on(struct adv7511 *adv7511)
> {
> adv7511->current_edid_segment = -1;
>
> - regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
> - ADV7511_INT0_EDID_READY);
> - regmap_write(adv7511->regmap, ADV7511_REG_INT(1),
> - ADV7511_INT1_DDC_ERROR);
> regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
> ADV7511_POWER_POWER_DOWN, 0);
> + if (adv7511->i2c_main->irq) {
> + /*
> + * Documentation says the INT_ENABLE registers are reset in
> + * POWER_DOWN mode. My tests with a 7511w show something else
> + * but let's stick to the documentation.
This contradicts the commit message, which one is correct ?
> + */
> + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
> + ADV7511_INT0_EDID_READY);
> + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
> + ADV7511_INT1_DDC_ERROR);
> + }
>
> /*
> * Per spec it is allowed to pulse the HDP signal to indicate that the
> @@ -567,12 +574,14 @@ static int adv7511_get_modes(struct drm_encoder
> *encoder,
>
> /* Reading the EDID only works if the device is powered */
> if (!adv7511->powered) {
> - regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
> - ADV7511_INT0_EDID_READY);
> - regmap_write(adv7511->regmap, ADV7511_REG_INT(1),
> - ADV7511_INT1_DDC_ERROR);
> regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
> ADV7511_POWER_POWER_DOWN, 0);
> + if (adv7511->i2c_main->irq) {
> + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
> + ADV7511_INT0_EDID_READY);
> + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
> + ADV7511_INT1_DDC_ERROR);
> + }
> adv7511->current_edid_segment = -1;
> }
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
