On 17.01.2025 18:28, Andy Shevchenko
wrote:
On Fri, Jan 17, 2025 at 05:05:42PM +0100, Marek Szyprowski wrote:On 17.01.2025 15:30, Andy Shevchenko wrote:On Fri, Jan 17, 2025 at 04:09:58PM +0200, Andy Shevchenko wrote:On Fri, Jan 17, 2025 at 02:57:52PM +0100, Marek Szyprowski wrote:On 16.01.2025 13:42, Andy Shevchenko wrote:If the selector register is represented in each page, its value in accordance to the debugfs is stale because it gets synchronized only after the real page switch happens. Synchronize cache for the page selector. Before (offset followed by hexdump, the first byte is selector): // Real registers 18: 05 ff 00 00 ff 0f 00 00 f0 00 00 00 ... // Virtual (per port) 40: 05 ff 00 00 e0 e0 00 00 00 00 00 1f 50: 00 ff 00 00 e0 e0 00 00 00 00 00 1f 60: 01 ff 00 00 ff ff 00 00 00 00 00 00 70: 02 ff 00 00 cf f3 00 00 00 00 00 0c 80: 03 ff 00 00 00 00 00 00 00 00 00 ff 90: 04 ff 00 00 ff 0f 00 00 f0 00 00 00 After: // Real registers 18: 05 ff 00 00 ff 0f 00 00 f0 00 00 00 ... // Virtual (per port) 40: 00 ff 00 00 e0 e0 00 00 00 00 00 1f 50: 01 ff 00 00 e0 e0 00 00 00 00 00 1f 60: 02 ff 00 00 ff ff 00 00 00 00 00 00 70: 03 ff 00 00 cf f3 00 00 00 00 00 0c 80: 04 ff 00 00 00 00 00 00 00 00 00 ff 90: 05 ff 00 00 ff 0f 00 00 f0 00 00 00 Fixes: 6863ca622759 ("regmap: Add support for register indirect addressing.") Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>This patch landed in linux-next some time ago as commit 1fd60ed1700c ("regmap: Synchronize cache for the page selector"). Today I've noticed that it causes a regression for Lontium LT9611UXC HDMI bridge driver.Is there any datasheet link to the HW in question? (FWIW, I have tested this with the CY8C9540 GPIO I²C expander on Intel Galileo Gen 1 board.)With today's linux-next I got the following messages on QCom RB5 board: # dmesg | grep lt9611uxc [ 13.737346] lt9611uxc 5-002b: LT9611 revision: 0x00.00.00 [ 13.804190] lt9611uxc 5-002b: LT9611 version: 0x00 [ 13.870564] lt9611uxc 5-002b: FW version 0, enforcing firmware update [ 13.877437] lt9611uxc 5-002b: Direct firmware load for lt9611uxc_fw.bin failed with error -2 [ 13.887517] lt9611uxc 5-002b: probe with driver lt9611uxc failed with error -2 after reverting the $subject patch, the driver probes fine on that board. I'm not sure if this is really a bug caused by this change or simply the driver already was aligned to old regmap behavior. Dmitry, could you check the regamp usage and review the changes introduced by this patch? Let me know if there is anything to check on the real hardware to help resolving this issue.Yes, see below. And thank you for your report!...+ /* + * If selector register has been just updated, update the respective + * virtual copy as well. + */ + if (page_chg && + in_range(range->selector_reg, range->window_start, range->window_len)) + _regmap_update_bits(map, sel_register, mask, val, NULL, false);Can you add a test printk() here to show page_chg range->selector_reg, range->window_start, range->window_len sel_register, mask, val ? And would commenting these three lines make it work again?Also try to apply this patch (while having the above lines not commented):This patch applied alone doesn't change anything. Probe still fails. However, with the mentioned 3 lines in the regmap code commented AND this patch applied, lt9611uxc driver probe also fails.Does it fail in the same way?
Yes, the hw revision is reported as zero in this case: LT9611 revision: 0x00.00.00
Does it mean that there is really a bug in the driver?Without looking at the datasheet it's hard to say. At least what I found so far is one page of the I²C traffic dump on Windows as an example how to use their evaluation board and software, but it doesn't unveil the bigger picture. At least what I think is going on here is that the programming is not so easy as just paging. Something is more complicated there. But at least (and as Mark said) the most of the regmap based drivers got the ranges wrong (so, at least there is one bug in the driver).
I can do more experiments if this helps. Do you need a dump of
all regmap accesses or i2c traffic from this driver?
--- a/drivers/gpu/drm/bridge/lontium-lt9611uxc.c +++ b/drivers/gpu/drm/bridge/lontium-lt9611uxc.c @@ -69,7 +69,7 @@ struct lt9611uxc { static const struct regmap_range_cfg lt9611uxc_ranges[] = { { .name = "register_range", - .range_min = 0, + .range_min = 0x0100, .range_max = 0xd0ff, .selector_reg = LT9611_PAGE_CONTROL, .selector_mask = 0xff,
Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland
|