Re: [PATCH] drm/dp_mst: Clear MSG_RDY flag before sending new message

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 18 Apr 2023, Wayne Lin <Wayne.Lin@xxxxxxx> wrote:
> [Why & How]
> The sequence for collecting down_reply/up_request from source
> perspective should be:
>
> Request_n->repeat (get partial reply of Request_n->clear message ready
> flag to ack DPRX that the message is received) till all partial
> replies for Request_n are received->new Request_n+1.
>
> While assembling partial reply packets, reading out DPCD DOWN_REP
> Sideband MSG buffer + clearing DOWN_REP_MSG_RDY flag should be
> wrapped up as a complete operation for reading out a reply packet.
> Kicking off a new request before clearing DOWN_REP_MSG_RDY flag might
> be risky. e.g. If the reply of the new request has overwritten the
> DPRX DOWN_REP Sideband MSG buffer before source writing ack to clear
> DOWN_REP_MSG_RDY flag, source then unintentionally flushes the reply
> for the new request. Should handle the up request in the same way.
>
> In drm_dp_mst_hpd_irq(), we don't clear MSG_RDY flag before caliing
> drm_dp_mst_kick_tx(). Fix that.
>
> Signed-off-by: Wayne Lin <Wayne.Lin@xxxxxxx>
> Cc: stable@xxxxxxxxxxxxxxx
> ---
>  .../gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c |  2 ++
>  drivers/gpu/drm/display/drm_dp_mst_topology.c | 22 +++++++++++++++++++
>  drivers/gpu/drm/i915/display/intel_dp.c       |  3 +++
>  drivers/gpu/drm/nouveau/dispnv50/disp.c       |  2 ++
>  4 files changed, 29 insertions(+)
>
> diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c
> index 77277d90b6e2..5313a5656598 100644
> --- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c
> +++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c
> @@ -3166,6 +3166,8 @@ static void dm_handle_mst_sideband_msg(struct amdgpu_dm_connector *aconnector)
>  			for (retry = 0; retry < 3; retry++) {
>  				uint8_t wret;
>  
> +				/* MSG_RDY ack is done in drm*/
> +				esi[1] &= ~(DP_DOWN_REP_MSG_RDY | DP_UP_REQ_MSG_RDY);

Why do the masking within the retry loop?

>  				wret = drm_dp_dpcd_write(
>  					&aconnector->dm_dp_aux.aux,
>  					dpcd_addr + 1,
> diff --git a/drivers/gpu/drm/display/drm_dp_mst_topology.c b/drivers/gpu/drm/display/drm_dp_mst_topology.c
> index 51a46689cda7..02aad713c67c 100644
> --- a/drivers/gpu/drm/display/drm_dp_mst_topology.c
> +++ b/drivers/gpu/drm/display/drm_dp_mst_topology.c
> @@ -4054,6 +4054,9 @@ int drm_dp_mst_hpd_irq(struct drm_dp_mst_topology_mgr *mgr, u8 *esi, bool *handl
>  {
>  	int ret = 0;
>  	int sc;
> +	const int tosend = 1;
> +	int retries = 0;
> +	u8 buf = 0;

All of these should be in tighter scope.

>  	*handled = false;
>  	sc = DP_GET_SINK_COUNT(esi[0]);
>  
> @@ -4072,6 +4075,25 @@ int drm_dp_mst_hpd_irq(struct drm_dp_mst_topology_mgr *mgr, u8 *esi, bool *handl
>  		*handled = true;
>  	}
>  
> +	if (*handled) {

That should check for DP_DOWN_REP_MSG_RDY and DP_UP_REQ_MSG_RDY only,
right? If those are not set, we didn't do anything with them, and should
not ack.

> +		buf = esi[1] & (DP_DOWN_REP_MSG_RDY | DP_UP_REQ_MSG_RDY);
> +		do {
> +			ret = drm_dp_dpcd_write(mgr->aux,
> +						DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0,
> +						&buf,
> +						tosend);

We should probably have a helper function to do the acking, similar to
intel_dp_ack_sink_irq_esi(), which could be used both by this function
and the drivers.

> +
> +			if (ret == tosend)
> +				break;
> +
> +			retries++;
> +		} while (retries < 5);

Please don't use a do-while when a for loop is sufficient.

	for (tries = 0; tries < 5; tries++)

and it's obvious at a glance how many times at most this runs. Not so
with a do-while where you count *re-tries*. Again, would be nice to
abstract this away in a helper function.

> +
> +		if (ret != tosend)
> +			drm_dbg_kms(mgr->dev, "failed to write dpcd 0x%x\n",
> +				    DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0);
> +	}
> +
>  	drm_dp_mst_kick_tx(mgr);
>  	return ret;
>  }
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> index bf80f296a8fd..abec3de38b66 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -3939,6 +3939,9 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
>  		if (!memchr_inv(ack, 0, sizeof(ack)))
>  			break;
>  
> +		/* MSG_RDY ack is done in drm*/
> +		ack[1] &= ~(DP_DOWN_REP_MSG_RDY | DP_UP_REQ_MSG_RDY);

Above we check if there's anything to ack and bail out, and now this
clears the bits but writes them anyway.

I think the handled parameter was problematic before, but now it's even
more convoluted. What does it indicate? It used to mean you need to ack
if it's set, but now it's something different. This function is getting
very difficult to use correctly.

BR,
Jani.



> +
>  		if (!intel_dp_ack_sink_irq_esi(intel_dp, ack))
>  			drm_dbg_kms(&i915->drm, "Failed to ack ESI\n");
>  	}
> diff --git a/drivers/gpu/drm/nouveau/dispnv50/disp.c b/drivers/gpu/drm/nouveau/dispnv50/disp.c
> index edcb2529b402..e905987104ed 100644
> --- a/drivers/gpu/drm/nouveau/dispnv50/disp.c
> +++ b/drivers/gpu/drm/nouveau/dispnv50/disp.c
> @@ -1336,6 +1336,8 @@ nv50_mstm_service(struct nouveau_drm *drm,
>  		if (!handled)
>  			break;
>  
> +		/* MSG_RDY ack is done in drm*/
> +		esi[1] &= ~(DP_DOWN_REP_MSG_RDY | DP_UP_REQ_MSG_RDY);
>  		rc = drm_dp_dpcd_write(aux, DP_SINK_COUNT_ESI + 1, &esi[1],
>  				       3);

Same here, this acks even if it's already been acked.

>  		if (rc != 3) {

-- 
Jani Nikula, Intel Open Source Graphics Center



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux