Re: [PATCH 1/2] Mips: ls2k1000: dts: add the display controller device node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 2023/2/23 16:05, Krzysztof Kozlowski wrote:
On 23/02/2023 08:58, Krzysztof Kozlowski wrote:
On 23/02/2023 04:19, Sui jingfeng wrote:
Hi,

On 2023/2/23 02:32, Krzysztof Kozlowski wrote:
On 22/02/2023 17:55, suijingfeng wrote:
The display controller is a pci device, it's pci vendor id is
0x0014, it's pci device id is 0x7a06.

Signed-off-by: suijingfeng <suijingfeng@xxxxxxxxxxx>
---
   .../boot/dts/loongson/loongson64-2k1000.dtsi  | 21 +++++++++++++++++++
   1 file changed, 21 insertions(+)

diff --git a/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
index 8143a61111e3..a528af3977d9 100644
--- a/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
+++ b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
@@ -31,6 +31,18 @@ memory@200000 {
   			<0x00000001 0x10000000 0x00000001 0xb0000000>; /* 6912 MB at 4352MB */
   	};
+ reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		display_reserved: framebuffer@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x30000000 0x0 0x04000000>; /* 64M */
+			linux,cma-default;
+		};
+	};
+
   	cpu_clk: cpu_clk {
   		#clock-cells = <0>;
   		compatible = "fixed-clock";
@@ -198,6 +210,15 @@ sata@8,0 {
   				interrupt-parent = <&liointc0>;
   			};
+ display-controller@6,0 {
+				compatible = "loongson,ls2k1000-dc";
+
+				reg = <0x3000 0x0 0x0 0x0 0x0>;
+				interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc0>;
+				memory-region = <&display_reserved>;
NAK.
Err :(,  please give me a chance to explain
Test your code against the bindings you send.
I can guarantee to you that I test may code more than twice. The code
used to testing is listed at link [1].
I wrote - test against the bindings. I don't believe that it was tested.
Please paste the output of the testing (dtbs_check).
OTOH, dtschema has some hickups on loongsoon DTS, so I doubt you could
even test it. Anyway, where is above property memory-region described in
the bindings?

Yes, you are right. I forget to write memory-region property.

but the code provided in  loongson64-2k1000.dtsi is correct.

I do run dt_binding_check, the results seems good.

there are some problem when make dtbs_check, but it seems not relevant to me.

please give me more time to figure it out, i will reply to you later.

Best regards,
Krzysztof




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux