On 2023-02-13 19:09:32, Abhinav Kumar wrote: > > > On 2/13/2023 1:46 PM, Dmitry Baryshkov wrote: > > On 13/02/2023 21:37, Jessica Zhang wrote: > >> > >> > >> On 12/31/2022 1:50 PM, Marijn Suijten wrote: > >>> All SoCs since DPU 5.0.0 (and seemingly up until and including 6.0.0, > >>> but excluding 7.x.x) have the tear interrupt and control registers moved > >>> out of the PINGPONG block and into the INTF block. Wire up the > >>> necessary interrupts and IRQ masks on all supported hardware. > >> > >> Hi Marijn, > >> > >> Thanks for the patch. > >> > >> I saw that in your commit msg, you mentioned that 7.x doesn't have > >> tearcheck in the INTF block -- can you double check that this is correct? It wasn't correct and has already been removed for v2 [1] after rebasing on top of SM8[345]50 support, where the registers reside at a different (named 7xxxx downstream) offset. [1] https://github.com/SoMainline/linux/commit/886d3fb9eed925e7e9c8d6ca63d2439eaec1c702 > >> I'm working on SM8350 (DPU v7) and I'm seeing that it does have > >> tearcheck in INTF block. > > > > I confirm, according to the vendor drivers INTF TE should be used for > > all DPU >= 5.0, including 7.x and 8.x > > > > However I think I know what Marijn meant here. For 5.x and 6.x these > > IRQs are handled at the address MDSS + 0x6e800 / + 0x6e900 (which means > > offset here should 0x6d800 and 0x6d900) for INTF_1 and INTF_2. Since DPU > > 7.x these IRQ registers were moved close to the main INTF block (0x36800 > > and 0x37800 = INTF + 0x800). That might have been the case. > Got it, then the commit text should remove "control" and just say tear > interrupt registers. It got a bit confusing. The wording here points to both the interrupt (MDP_INTFx_TEAR_INTR) registers and control (INTF_TEAR_xxx) registers separately. Feel free to bikeshed the wording in preliminary v2 [1]; should I drop the mention of the control registers being "moved" from PP to INTF entirely, leaving just the wording about the interrupt registers moving from MDP_SSPP_TOP0_INTR to a dedicated MDP_INTFx_TEAR_INTR region? > We will add the 7xxx intf tear check support on top of this series. No need, that is already taken care of in an impending v2 [1] (unless additional changes are required beyond the moved register offset). > >>> Signed-off-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx> > >>> --- > >>> .../gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 78 +++++++++++-------- > >>> .../gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 6 +- > >>> .../gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.c | 12 +++ > >>> .../gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.h | 2 + > >>> drivers/gpu/drm/msm/disp/dpu1/dpu_hwio.h | 3 + > >>> 5 files changed, 68 insertions(+), 33 deletions(-) > >>> > >>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c > >>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c > >>> index 1cfe94494135..b9b9b5b0b615 100644 > >>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c > >>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c > >>> @@ -86,6 +86,15 @@ > >>> #define INTF_SC7280_MASK INTF_SC7180_MASK | BIT(DPU_DATA_HCTL_EN) > >>> +#define IRQ_MSM8998_MASK (BIT(MDP_SSPP_TOP0_INTR) | \ > >>> + BIT(MDP_SSPP_TOP0_INTR2) | \ > >>> + BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> + BIT(MDP_INTF0_INTR) | \ > >>> + BIT(MDP_INTF1_INTR) | \ > >>> + BIT(MDP_INTF2_INTR) | \ > >>> + BIT(MDP_INTF3_INTR) | \ > >>> + BIT(MDP_INTF4_INTR)) > >>> + > >>> #define IRQ_SDM845_MASK (BIT(MDP_SSPP_TOP0_INTR) | \ > >>> BIT(MDP_SSPP_TOP0_INTR2) | \ > >>> BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> @@ -100,13 +109,15 @@ > >>> #define IRQ_QCM2290_MASK (BIT(MDP_SSPP_TOP0_INTR) | \ > >>> BIT(MDP_SSPP_TOP0_INTR2) | \ > >>> BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> - BIT(MDP_INTF1_INTR)) > >>> + BIT(MDP_INTF1_INTR) | \ > >>> + BIT(MDP_INTF1_TEAR_INTR)) > >>> #define IRQ_SC7180_MASK (BIT(MDP_SSPP_TOP0_INTR) | \ > >>> BIT(MDP_SSPP_TOP0_INTR2) | \ > >>> BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> BIT(MDP_INTF0_INTR) | \ > >>> - BIT(MDP_INTF1_INTR)) > >>> + BIT(MDP_INTF1_INTR) | \ > >>> + BIT(MDP_INTF1_TEAR_INTR)) > >>> #define IRQ_SC7280_MASK (BIT(MDP_SSPP_TOP0_INTR) | \ > >>> BIT(MDP_SSPP_TOP0_INTR2) | \ > >>> @@ -120,7 +131,9 @@ > >>> BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> BIT(MDP_INTF0_INTR) | \ > >>> BIT(MDP_INTF1_INTR) | \ > >>> + BIT(MDP_INTF1_TEAR_INTR) | \ > >>> BIT(MDP_INTF2_INTR) | \ > >>> + BIT(MDP_INTF2_TEAR_INTR) | \ > >>> BIT(MDP_INTF3_INTR) | \ > >>> BIT(MDP_INTF4_INTR)) > >>> @@ -129,7 +142,9 @@ > >>> BIT(MDP_SSPP_TOP0_HIST_INTR) | \ > >>> BIT(MDP_INTF0_INTR) | \ > >>> BIT(MDP_INTF1_INTR) | \ > >>> + BIT(MDP_INTF1_TEAR_INTR) | \ > >>> BIT(MDP_INTF2_INTR) | \ > >>> + BIT(MDP_INTF2_TEAR_INTR) | \ > >>> BIT(MDP_INTF3_INTR) | \ > >>> BIT(MDP_INTF4_INTR) | \ > >>> BIT(MDP_INTF5_INTR) | \ > >>> @@ -1300,63 +1315,64 @@ static struct dpu_dsc_cfg sdm845_dsc[] = { > >>> /************************************************************* > >>> * INTF sub blocks config > >>> *************************************************************/ > >>> -#define INTF_BLK(_name, _id, _base, _type, _ctrl_id, _progfetch, > >>> _features, _reg, _underrun_bit, _vsync_bit) \ > >>> +#define INTF_BLK(_name, _id, _base, _len, _type, _ctrl_id, > >>> _progfetch, _features, _reg, _underrun_bit, _vsync_bit, _tear_reg, > >>> _tear_rd_ptr_bit) \ > >>> {\ > >>> .name = _name, .id = _id, \ > >>> - .base = _base, .len = 0x280, \ > >>> + .base = _base, .len = _len, \ > >>> .features = _features, \ > >>> .type = _type, \ > >>> .controller_id = _ctrl_id, \ > >>> .prog_fetch_lines_worst_case = _progfetch, \ > >>> .intr_underrun = DPU_IRQ_IDX(_reg, _underrun_bit), \ > >>> .intr_vsync = DPU_IRQ_IDX(_reg, _vsync_bit), \ > >>> + .intr_tear_rd_ptr = DPU_IRQ_IDX(_tear_reg, _tear_rd_ptr_bit), \ > >>> } > >>> static const struct dpu_intf_cfg msm8998_intf[] = { > >>> - INTF_BLK("intf_0", INTF_0, 0x6A000, INTF_DP, 0, 25, > >>> INTF_SDM845_MASK, MDP_SSPP_TOP0_INTR, 24, 25), > >>> - INTF_BLK("intf_1", INTF_1, 0x6A800, INTF_DSI, 0, 25, > >>> INTF_SDM845_MASK, MDP_SSPP_TOP0_INTR, 26, 27), > >>> - INTF_BLK("intf_2", INTF_2, 0x6B000, INTF_DSI, 1, 25, > >>> INTF_SDM845_MASK, MDP_SSPP_TOP0_INTR, 28, 29), > >>> - INTF_BLK("intf_3", INTF_3, 0x6B800, INTF_HDMI, 0, 25, > >>> INTF_SDM845_MASK, MDP_SSPP_TOP0_INTR, 30, 31), > >>> + INTF_BLK("intf_0", INTF_0, 0x6A000, 0x268, INTF_DP, 0, 25, > >>> INTF_SDM845_MASK, MDP_SSPP_TOP0_INTR, 24, 25, -1, -1), > >> > >> Just wondering, how were the lengths calculated for the INTF blocks? > >> The values in general seem a little off to me. These (for MSM8998) have been taken from downstream specifically; my series starts using INTF_STATUS at 0x26C which conveniently is the register right after 0x268, matching the fact that INTF TE and these registers weren't supported/available yet on MSM8998. > >> For example, I'm looking downstream and it seems to me that the length > >> for the INTF_0 on MSM8998 should be 0x280. Similarly for SC7280, I'm > >> seeing that length for INTF + tearcheck should be 0x2c4. There are many different downstream sources and tags with seemingly conflicting/confusing information. For v2 [2] I've picked the highest register used by the driver which is INTF_TEAR_AUTOREFRESH_CONFIG at 0x2B4 (but there might always be more registers that don't need to be poked at by the driver, but contain magic debug information and the like... those would be useful to capture in the dump going forward). [2]: https://github.com/SoMainline/linux/commit/2bbc609dd28aa0bd0a2dede20163e521912d0072 > > We have discussed INTF lengths in [1]. The current understanding of the > > block lengths can be found at [2]. Please comment there if any of the > > fixed lengths sounds incorrect to you. > > > > [1] https://patchwork.freedesktop.org/patch/522187/ > > [2] https://patchwork.freedesktop.org/patch/522227/ > > > > [skipped the rest] > > > > Please correct my understanding here, it was agreed to fix intf blocks > to 0x2c4 here https://patchwork.freedesktop.org/patch/522227/ but I dont > see this was merged? > > It was agreed to first land INTF_TE and then add the higher addresses Seems like it, at least if I interpret [3] correctly. My series adds a new define that will hardcode _len to 0x2B8 for now, and Dmitry/Konrad can later extend it to whatever is stated by the correct downstream source. [3]: https://lore.kernel.org/linux-arm-msm/6ad96cff-b91b-a4c7-4573-7bb8de7194f8@xxxxxxxxxx/ > but I dont see such a change, am i missing something? This was discussed just yesterday. And it wouldn't make much sense to make such a change now, knowing that my v2 for this series - which isn't even on the lists yet - will already change the INTF_BLK macro resulting in unneeded conflicts. As requested by Dmitry, let's get INTF TE processed first before rebasing the block length change? - Marijn
