On Thu, Nov 18, 2021 at 12:52 PM Tim Harvey <tharvey@xxxxxxxxxxxxx> wrote: > > On Thu, Nov 18, 2021 at 10:30 AM Dave Stevenson > <dave.stevenson@xxxxxxxxxxxxxxx> wrote: > > > > On Thu, 18 Nov 2021 at 17:36, Tim Harvey <tharvey@xxxxxxxxxxxxx> wrote: > > > > > > On Thu, Nov 18, 2021 at 6:28 AM Dave Stevenson > > > <dave.stevenson@xxxxxxxxxxxxxxx> wrote: > > > > > > > > Hi Tim > > > > > > > > On Thu, 18 Nov 2021 at 01:26, Tim Harvey <tharvey@xxxxxxxxxxxxx> wrote: > > > > > > > > > > Greetings, > > > > > > > > > > I'm trying to get a RPI 7" touchscreen display working on an IMX8MM > > > > > board and while I've been able to get the MIPI DSI display and > > > > > backlight working I still can't seem to figure out the touch > > > > > controller. > > > > > > > > > > It's supposed to have an FT5406 controller on it without an interrupt > > > > > so I added polling support drivers/input/touchscreen/edt-ft5x06.c > > > > > which I was able to verify using another touchscreen with that > > > > > controller but when reading data from the FT5406 on the RPI controller > > > > > the data does not make sense. > > > > > > > > > > These panels appear to route the I2C from the FT5406 to a STM32F103 > > > > > MPU that then provides a different I2C slave interface to the 15pin > > > > > connector that I'm connected to. On that I2C interface I see an i2c > > > > > slave at 0x45 which is managed by the regulator driver Marek wrote > > > > > (drivers/regulator/rpi-panel-attiny-regulator.c) and there is also an > > > > > i2c slave at 0x38 which I assumed was the FT5406 but I believe the MPU > > > > > is perhaps obfuscating that touch data. > > > > > > > > > > Anyone have any ideas on how to make that touch controller useful? > > > > > > > > There should be nothing unusual. 0x38 is the EDT touch controller. > > > > Starting with the Raspberry Pi OS Bullseye release, we're now using > > > > the panel directly from DRM rather than through the firmware. That's > > > > based on the branch at > > > > https://github.com/raspberrypi/linux/tree/rpi-5.10.y/ > > > > > > > > > > Dave, > > > > > > That sounds like the driver that made it into mainline with Eric's > > > commit 2f733d6194bd ("drm/panel: Add support for the Raspberry Pi 7" > > > Touchscreen."). I looked there but that driver just deals with the DSI > > > and not with touch. > > > > No, we've reverted away from that driver as it exposes no regulator > > framework either, so again the touch element loses power. > > > > > > I also added polling support to edt-ft5x04.c. > > > > For DT, it uses a combination of the overlays vc4-kms-v3d, > > > > vc4-kms-dsi-7inch, and that includes edt-ft5406.dtsi, all of which are > > > > in /arch/arm/boot/dts/overlays > > > > > > It doesn't look like you ever submitted your edt-ft5x04 polling mode > > > support upstream. I saw another series to add polling support > > > submitted by Nicolas back in 2019 but was never followed up on > > > (https://patchwork.kernel.org/project/linux-input/list/?series=112187&archive=both). > > > > No I haven't as it's been crazy trying to get this lot to work under > > KMS at all over the last couple of months. > > > > > I have updated Nicolas' patch with the changes requested and am happy > > > to submit it upstream. The benefit of his patch is that it uses a dt > > > binding for the polling interval. I'm happy to submit this upstream. > > > > I hadn't seen Nicolas' patches, hence implementing it myself. > > > > If you've implemented the requested changes, could you check that the > > polling rate is as expected? We were seeing that the input framework > > wasn't delivering the requested poll rate when CONFIG_HZ=100 is > > defined in the config. I must confess that I haven't checked it on my > > current patch, but it was on my list of things to do. > > There was a report that "bd88ce25335d Input: raspberrypi-ts - switch > > to using polled mode of input devices" dropped the polling rate from > > the desired 60Hz in switching to that framework. > > Ok, I'll make a note to test that and submit it. > > > > > > > > > > > The main issue I had was configuring the regulator framework > > > > appropriately to allow the touch controller power to be separate from > > > > the bridge power. Without that if DRM powered down the panel it killed > > > > the touch controller too, and the touch driver never reinitialised > > > > itself. > > > > > > I'm using the same drivers/regulator/rpi-panel-attiny-regulator.c > > > regulator driver from mainline that Marek added as the power-supply > > > for the panel as well as the backlight controller. It looks like the > > > version in the rpi-5.10.y has several patches on top of it so I'll > > > take a look at those differences to see if it may be affecting the > > > touchscreen controller. It's really strange to me that the touch > > > controller's I2C goes through the STM32F103 MPU (as in the MPU's I2C > > > master connects to the touchscreen controller and a different MPU I2C > > > bus presents the touch controller like they are translating > > > something?). > > > > The touchscreen I2C does NOT go through the STM. > > The TS interrupt line does feed into the STM, but it's not actually used. > > The TC358762 I2C does go through the STM, but it isn't used other than > > a kick to bring the bridge out of reset. > > Ok, I've determined the DFROBOT Rpi displays do differ from the > official Rpi 7in display. > > Official 7in RPI display: > - I can't find a schematic anywhere for the official display but I an > ohmmeter confirms your claim that the touch controller I2C is > connected to the 15pin display I2C. > - I do not see the ft5406@0x38 on the i2c bus until I send a command a > REG_POWERON cmdto the ATTINY@0x45 'i2c dev 2 && i2c mw 0x45 0x85 1 1' > in u-boot > - I must disable the rpi-panel-attiny-regulator.c driver as its probe > disables REG_POWERON and the linux driver won't see the FT5406 > - The linux edt-ft5x06.c driver with polling added works fine and > gives me expected touch events > > With the DFROBOT 5in and 7in displays: > - the touch interface I2C does not connect directly to the 15pin > connector's I2C (shown in the schematic at schematic: > https://github.com/DFRobot/Wiki/raw/master/DFR0550_Schematics.pdf and > also verified with an ohmeter) > - I see the ft5406@0x38 on the i2c bus regardless of setting or > clearing REG_POWERON on the ATTINY@0x45 > - The linux edt-ft5x06.c driver with polling added gives me data that > does not make sense for touch events > > So I can only assume the DFROBOT displays are doing something strange > but I'm not clear how what they are doing is compatible with the RPI. > I guess I have to get an RPI, hook it up and see if the touch screen > works with the rpi 5.10.y kernel. > > > > > > I wonder if I'm hitting that reinitialization issue. Do you recall any > > > details about that? Was it that the driver returned seemingly invalid > > > touch data like I'm getting or did it just not respond? > > > > If the power goes down then all the registers written during probe [1] > > are reset. I don't recall exactly what the data then contained, but I > > did get a load of I2C transactions fail with -EREMOTEIO as the > > messages weren't ACKed. > > > > [1] https://elixir.bootlin.com/linux/latest/source/drivers/input/touchscreen/edt-ft5x06.c#L1207 > > > > > Silly question likely but how do I power down the DRM portion to test > > > to see if it affects the touch controller? > > > > xrandr --output DSI-1 --off > > There must be a libdrm call to do the equivalent, but I'll admit that > > I can't think of an existing tool that implements it. > > do you know of a sysfs way to do this or something that doesn't require xrandr? > > > > > > > On our branch rpi-panel-attiny-regulator.c has been updated to control > > > > those functions independently as GPIOs, which then get used via > > > > regulator-fixed, or as reset-gpios. > > > > Telling both bridge and touch that they shared a regulator didn't work > > > > as the DSI bridge seems mildly fussy about the DSI state when it is > > > > powered up. > > > > > > Hmm... I wonder if this is the problem I had with the 'official' rpi > > > 7in display that I never got working. I did get the DFROBOT rpi 5in > > > and 7in displays working. > > > > I'm not that familiar with the DFRobot displays. > > I have tried an Osoyoo 3.5" panel [2] that pretends to be the Pi > > panel, and it looks similar. Reality is that it uses a Lattice FPGA to > > convert from DSI to DPI. All the LP configuration commands sent to it > > are ignored. Startup requirements of that compared to the Toshiba are > > unknown. > > > > [2] https://www.amazon.co.uk/OSOYOO-Capacitive-Connector-Resolution-Raspberry/dp/B087WVC1J2 > > > > > > Hope that helps. > > > > > > > > > > The fact you tell me that the rpi-5.10.y branch goes away from the > > > strange 'firmware' driver I found at > > > https://github.com/raspberrypi/linux/blob/rpi-4.2.y/drivers/input/touchscreen/rpi-ft5406.c > > > and uses the standard ft5406.c driver (with polling mode added) is > > > very helpful in that I feel I have a hope of getting this working. > > > > I have one of our panels working in front of me using my patched > > version of edt-ft5x06 as the driver for the touch element. > > > > > Does the rpi-5.10.y kernel work for the official rpi 7in display as > > > well as the DFROBOT displays as far as you know? > > > > As above, I'm not aware of DFRobot. > > With the Osoyoo I can't recall exactly what it was doing with I2C. I > > think it only really responded to the ID command and PWM for the > > backlight. The reset and power control that is required on our boards > > isn't really relevant to them. > > I was doing i2cset -y -f <bus> 0x45 0x85 [1|0] to turn power on/off, > > and I seem to recall it did nothing. > > Right... this is also the same with the DFROBOT touchscreen displays. > > I do really like the build quality, availability, and pricing of the > DFROBOT displays but also a huge advantage is that they derive power > from the 15pin connector 3.3V pins so there are no other connections. > Their backlight doesn't appear to be controllable via PWM however and > instead they have a manual brightness thumbwheel on them. > > The other advantage for me at the moment is that I still haven't > gotten the official RPI 7in display to work with the IMX8MM (no pixels > displayed) where as the DFROBOT one is working for me. > > > ... > > Just for you I fired it up. It ACKs all I2C addresses just for a > > laugh, and indeed it takes no action on 0x85, only 0x86 (for PWM), and > > reading 0x80 (ID). > > > Dave, After some more investigation I've found that while the DFRobot DRF0550 and DFR0678 touch controller does not work with the ft5x06 driver it does indeed work on a Rpi with the raspberrypi-ts driver. So from an Rpi perspective the latest OS image doesn't work but the 'Legacy' OS image does (which appears to have the same 5.10 kernel but uses legacy drivers?). So if I understand correctly the Rpi has some firmware that talks over I2C and translates touch events from this 'legacy API' over to a memory mapped area. How can I learn about this firmware and what kind of translation it does to make these touch controllers work on a non rpi? Best Regards, Tim
