On Tue, Nov 9, 2021 at 11:34 AM Tim Harvey <tharvey@xxxxxxxxxxxxx> wrote: > > Add nodes for MIPI DSI and LCDIF on IMX8MM > > I'm currently working with a set of patches to convert drm/exynos > to a bridge [1] and add IMX8MM support [2] in order to get IMX8MM DSI > working for display with a Raspberry Pi DSI touchscreen compatible with > a Toshiba TC358762 DSI bridge and Powertip PH800480T013-IDF02 > touchscreen. > > I had this working on a 5.10 kernel with the old blk-ctl and > power-domain drivers that didn't make it into mainline but my 5.15 > series with blk-ctl backported from next hangs right after > "[drm] Initialized mxsfb-drm 1.0.0 20160824 for 32e00000.lcdif on minor 0" > so I assume I have a power-domain not getting enabled. > > Please let me know if you see an issue with the way I've configured > power-domain or clocks here. > > Best Regards, > > Tim > [1] https://patchwork.kernel.org/project/dri-devel/list/?series=347439&archive=both&state=* > [2] https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=359775&archive=both&state=* > --- > arch/arm64/boot/dts/freescale/imx8mm.dtsi | 68 +++++++++++++++++++++++ > 1 file changed, 68 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi > index 208a0ed840f4..195dcbff7058 100644 > --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi > +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi > @@ -188,6 +188,12 @@ > clock-output-names = "clk_ext4"; > }; > > + mipi_phy: mipi-video-phy { > + compatible = "fsl,imx8mm-mipi-video-phy"; > + syscon = <&disp_blk_ctrl>; > + #phy-cells = <1>; > + }; > + > psci { > compatible = "arm,psci-1.0"; > method = "smc"; > @@ -1068,6 +1074,68 @@ > #size-cells = <1>; > ranges = <0x32c00000 0x32c00000 0x400000>; > > + lcdif: lcdif@32e00000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fsl,imx8mm-lcdif", "fsl,imx6sx-lcdif"; The compatible "imx6sx-lcdif" implies MXSFB_V6. FWICT, it is like MXSFB_V4, but with overlays and those overlays have more registers configured in the mxsfb_kms driver. Have you tried using imx28-lcdif to see if it makes a difference? > + reg = <0x32e00000 0x10000>; > + clocks = <&clk IMX8MM_CLK_LCDIF_PIXEL>, > + <&clk IMX8MM_CLK_DISP_AXI_ROOT>, > + <&clk IMX8MM_CLK_DISP_APB_ROOT>; > + clock-names = "pix", "disp_axi", "axi"; > + assigned-clocks = <&clk IMX8MM_CLK_LCDIF_PIXEL>, > + <&clk IMX8MM_CLK_DISP_AXI>, > + <&clk IMX8MM_CLK_DISP_APB>; > + assigned-clock-parents = <&clk IMX8MM_VIDEO_PLL1_OUT>, > + <&clk IMX8MM_SYS_PLL2_1000M>, > + <&clk IMX8MM_SYS_PLL1_800M>; > + assigned-clock-rate = <594000000>, <500000000>, <200000000>; Just through visual inspection, it appears that the IMX8MM_CLK_DISP_AXI and IMX8MM_CLK_DISP_APB clock-parents and rates are already set in the pgc_dispmix, so I think it's safe to reduce those lines to just assigning IMX8MM_CLK_LCDIF_PIXEL to the IMX8MM_VIDEO_PLL1_OUT with the assigned-clock-rate set to 594000000. adam > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_LCDIF>; > + status = "disabled"; > + > + port@0 { > + reg = <0>; > + > + lcdif_to_dsim: endpoint { > + remote-endpoint = <&dsim_from_lcdif>; > + }; > + }; > + }; > + > + mipi_dsi: mipi_dsi@32e10000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fsl,imx8mm-mipi-dsim"; > + reg = <0x32e10000 0x400>; > + clocks = <&clk IMX8MM_CLK_DSI_CORE>, > + <&clk IMX8MM_CLK_DSI_PHY_REF>; > + clock-names = "bus_clk", "sclk_mipi"; > + assigned-clocks = <&clk IMX8MM_CLK_DSI_CORE>, > + <&clk IMX8MM_VIDEO_PLL1_OUT>, > + <&clk IMX8MM_CLK_DSI_PHY_REF>; > + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>, > + <&clk IMX8MM_VIDEO_PLL1_BYPASS>, > + <&clk IMX8MM_VIDEO_PLL1_OUT>; > + assigned-clock-rates = <266000000>, <594000000>, <27000000>; > + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; > + phys = <&mipi_phy 0>; > + phy-names = "dsim"; > + power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_MIPI_DSI>; > + samsung,burst-clock-frequency = <891000000>; > + samsung,esc-clock-frequency = <54000000>; > + samsung,pll-clock-frequency = <27000000>; > + status = "disabled"; > + > + port@0 { > + reg = <0>; > + > + dsim_from_lcdif: endpoint { > + remote-endpoint = <&lcdif_to_dsim>; > + }; > + }; > + }; > + > csi: csi@32e20000 { > compatible = "fsl,imx8mm-csi", "fsl,imx7-csi"; > reg = <0x32e20000 0x1000>; > -- > 2.17.1 >
