Hi Doug,
On Mon, Jun 21, 2021 at 08:34:51AM -0700, Doug Anderson wrote:
> Hi,
>
> On Sun, Jun 20, 2021 at 3:01 AM Sam Ravnborg <sam@xxxxxxxxxxxx> wrote:
> >
> > Hi Rajeev
> > On Sat, Jun 19, 2021 at 04:10:30PM +0530, Rajeev Nandan wrote:
> > > Add Samsung 13.3" FHD eDP AMOLED panel.
> > >
> > > Signed-off-by: Rajeev Nandan <rajeevny@xxxxxxxxxxxxxx>
> > > Reviewed-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> > > ---
> > >
> > > Changes in v4:
> > > - New
> > >
> > > Changes in v5:
> > > - Remove "uses_dpcd_backlight" property, not required now. (Douglas)
> > >
> > > Changes in v7:
> > > - Update disable_to_power_off and power_to_enable delays. (Douglas)
> > >
> > > drivers/gpu/drm/panel/panel-simple.c | 33 +++++++++++++++++++++++++++++++++
> > > 1 file changed, 33 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> > > index 86e5a45..4adc44a 100644
> > > --- a/drivers/gpu/drm/panel/panel-simple.c
> > > +++ b/drivers/gpu/drm/panel/panel-simple.c
> > > @@ -3562,6 +3562,36 @@ static const struct panel_desc rocktech_rk101ii01d_ct = {
> > > .connector_type = DRM_MODE_CONNECTOR_LVDS,
> > > };
> > >
> > > +static const struct drm_display_mode samsung_atna33xc20_mode = {
> > > + .clock = 138770,
> > > + .hdisplay = 1920,
> > > + .hsync_start = 1920 + 48,
> > > + .hsync_end = 1920 + 48 + 32,
> > > + .htotal = 1920 + 48 + 32 + 80,
> > > + .vdisplay = 1080,
> > > + .vsync_start = 1080 + 8,
> > > + .vsync_end = 1080 + 8 + 8,
> > > + .vtotal = 1080 + 8 + 8 + 16,
> > > + .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> > > +};
> > > +
> > > +static const struct panel_desc samsung_atna33xc20 = {
> > > + .modes = &samsung_atna33xc20_mode,
> > > + .num_modes = 1,
> > > + .bpc = 10,
> > > + .size = {
> > > + .width = 294,
> > > + .height = 165,
> > > + },
> > > + .delay = {
> > > + .disable_to_power_off = 200,
> > > + .power_to_enable = 400,
> > > + .hpd_absent_delay = 200,
> > > + .unprepare = 500,
> > > + },
> > > + .connector_type = DRM_MODE_CONNECTOR_eDP,
> > > +};
> >
> > bus_format is missing. There should be a warning about this when you
> > probe the display.
>
> Sam: I'm curious about the requirement of hardcoding bus_format like
> this for eDP panels. Most eDP panels support a variety of bits per
> pixel and do so dynamically. Ones I've poked at freely support 6bpp
> and 8bpp. Presumably this one supports both of those modes and also
> 10bpp. I haven't done detailed research on it, but it would also
> surprise me if the "bus format" for a given bpp needed to be specified
> for eDP. Presumably since eDP has most of the "autodetect" type
> features of DP then if the format needed to be accounted for that you
> could query the hardware?
>
> Looking at the datasheet for the ti-sn65dsi86 MIPI-to-eDP bridge chip
> I see that it explicitly calls out the bus formats that it supports
> for the MIPI side but doesn't call out anything for eDP. That would
> tend to support my belief that there isn't variance on the eDP side...
>
> Maybe the right fix is to actually change the check not to give a
> warning for eDP panels? ...or am I misunderstanding?
I have never dived into the datasheets of eDP panels so I do not know.
The checks were added based on what we had in-tree and it is no suprise
if they need an update or are just plain wrong.
I expect you to be in a better position to make the call here - but we
should not add panels that triggers warnings so either fix the warnings
or fix the panel description.
Sam
