On 1/13/21 10:42 AM, Maxime Ripard wrote:
Hi,
On Mon, Jan 11, 2021 at 06:46:16PM +0100, Giulio Benetti wrote:
From: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
During commit 88bc4178568b ("drm: Use new
DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags") DRM_BUS_FLAG_*
macros have been changed to avoid ambiguity but just because of this
ambiguity previous DRM_BUS_FLAG_PIXDATA_(POS/NEG)EDGE were used meaning
_SAMPLE_ not _DRIVE_. This leads to DLCK inversion and need to fix but
instead of swapping phase values, let's adopt an easier approach Maxime
suggested:
It turned out that bit 26 of SUN4I_TCON0_IO_POL_REG is dedicated to
invert DCLK polarity and this makes things really easier than before. So
let's handle DCLK polarity by adding SUN4I_TCON0_IO_POL_DCLK_POSITIVE as
bit 26 and activating according to bus_flags the same way it is done for
all the other signals polarity.
Fixes: 88bc4178568b ("drm: Use new DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags")
Suggested-by: Maxime Ripard <maxime@xxxxxxxxxx>
Signed-off-by: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/sun4i/sun4i_tcon.c | 20 +-------------------
drivers/gpu/drm/sun4i/sun4i_tcon.h | 1 +
2 files changed, 2 insertions(+), 19 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index eaaf5d70e352..30171ccd87e5 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -569,26 +569,8 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
if (info->bus_flags & DRM_BUS_FLAG_DE_LOW)
val |= SUN4I_TCON0_IO_POL_DE_NEGATIVE;
- /*
- * On A20 and similar SoCs, the only way to achieve Positive Edge
- * (Rising Edge), is setting dclk clock phase to 2/3(240°).
- * By default TCON works in Negative Edge(Falling Edge),
- * this is why phase is set to 0 in that case.
- * Unfortunately there's no way to logically invert dclk through
- * IO_POL register.
- * The only acceptable way to work, triple checked with scope,
- * is using clock phase set to 0° for Negative Edge and set to 240°
- * for Positive Edge.
- * On A33 and similar SoCs there would be a 90° phase option,
- * but it divides also dclk by 2.
- * Following code is a way to avoid quirks all around TCON
- * and DOTCLOCK drivers.
- */
if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE)
- clk_set_phase(tcon->dclk, 240);
-
- if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
- clk_set_phase(tcon->dclk, 0);
+ val |= SUN4I_TCON0_IO_POL_DCLK_POSITIVE;
regmap_update_bits(tcon->regs, SUN4I_TCON0_IO_POL_REG,
SUN4I_TCON0_IO_POL_HSYNC_POSITIVE |
You need to add SUN4I_TCON0_IO_POL_DCLK_POSITIVE to the mask you're
going to change here too
Ah, lost it during squash, I send a v4.
Thank you
Best regards
--
Giulio Benetti
Benetti Engineering sas
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
