Philippe Schenker <philippe.schenker@xxxxxxxxxxx> 于 2020年4月30日周四 20:08写道：
On Thu, 2020-04-30 at 17:43 +0800, dillon.minfei@xxxxxxxxx wrote:
> From: dillon min <dillon.minfei@xxxxxxxxx>
>
> Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
> ---
> .../bindings/display/panel/ilitek,ili9341.txt | 42 +++++++++++
> arch/arm/boot/dts/stm32f4-pinctrl.dtsi | 79
> +++++++++++++++++++
> arch/arm/boot/dts/stm32f429-disco.dts | 88
> ++++++++++++++++++++++
> arch/arm/boot/dts/stm32f429.dtsi | 12 +++
> 4 files changed, 221 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
>
> diff --git
> a/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> new file mode 100644
> index 0000000..f5a4e55
> --- /dev/null
> +++
> b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> @@ -0,0 +1,42 @@
> +Ilitek ILI9341 TFT panel driver with SPI control bus
> +
> +This is a driver for 240x320 TFT panels, accepting a rgb input
> +streams that get adapted and scaled to the panel.
> +
> +Required properties:
> + - compatible: "stm32f429-disco,ltdc-panel", "ilitek,ili9341"
> + (full system-specific compatible is always required to look up
> configuration)
> + - reg: address of the panel on the SPI bus
> +
> +Optional properties:
> + - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
> + - dc-gpios: a GPIO spec for the dc pin, see gpio/gpio.txt
> +
> + The following optional properties only apply to RGB input mode:
> +
> + - pixelclk-active: see display/panel/display-timing.txt
> + - de-active: see display/panel/display-timing.txt
> + - hsync-active: see display/panel/display-timing.txt
> + - vsync-active: see display/panel/display-timing.txt
> +
> +The panel must obey the rules for a SPI slave device as specified in
> +spi/spi-bus.txt
> +
> +The device node can contain one 'port' child node with one child
> +'endpoint' node, according to the bindings defined in
> +media/video-interfaces.txt. This node should describe panel's video
> bus.
> +
> +Example:
> +
> +panel: display@0 {
> + compatible = "stm32f429-disco,ltdc-panel", "ilitek,ili9341";
> + reg = <0>;
> + spi-3wire;
> + spi-max-frequency = <10000000>;
> + dc-gpios = <&gpiod 13 0>;
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&display_out>;
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> index 392fa14..45b68f4 100644
> --- a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> @@ -316,6 +316,85 @@
> };
> };
>
> + ltdc_pins_f429_disco: ltdc-1 {
> + pins {
> + pinmux = <STM32_PINMUX('C',
> 6, AF14)>,
> + /* LCD_HSYNC */
> + <STM32_PINMUX('A',
> 4, AF14)>,
> + /* LCD_VSYNC */
> + <STM32_PINMUX('G',
> 7, AF14)>,
> + /* LCD_CLK */
> + <STM32_PINMUX('C', 10,
> AF14)>,
> + /* LCD_R2 */
> + <STM32_PINMUX('B',
> 0, AF9)>,
> + /* LCD_R3 */
> + <STM32_PINMUX('A', 11,
> AF14)>,
> + /* LCD_R4 */
> + <STM32_PINMUX('A', 12,
> AF14)>,
> + /* LCD_R5 */
> + <STM32_PINMUX('B',
> 1, AF9)>,
> + /* LCD_R6*/
> + <STM32_PINMUX('G',
> 6, AF14)>,
> + /* LCD_R7 */
> + <STM32_PINMUX('A',
> 6, AF14)>,
> + /* LCD_G2 */
> + <STM32_PINMUX('G', 10,
> AF9)>,
> + /* LCD_G3 */
> + <STM32_PINMUX('B', 10,
> AF14)>,
> + /* LCD_G4 */
> + <STM32_PINMUX('D',
> 6, AF14)>,
> + /* LCD_B2 */
> + <STM32_PINMUX('G', 11,
> AF14)>,
> + /* LCD_B3*/
> + <STM32_PINMUX('B', 11,
> AF14)>,
> + /* LCD_G5 */
> + <STM32_PINMUX('C',
> 7, AF14)>,
> + /* LCD_G6 */
> + <STM32_PINMUX('D',
> 3, AF14)>,
> + /* LCD_G7 */
> + <STM32_PINMUX('G', 12,
> AF9)>,
> + /* LCD_B4 */
> + <STM32_PINMUX('A',
> 3, AF14)>,
> + /* LCD_B5 */
> + <STM32_PINMUX('B',
> 8, AF14)>,
> + /* LCD_B6 */
> + <STM32_PINMUX('B',
> 9, AF14)>,
> + /* LCD_B7 */
> + <STM32_PINMUX('F', 10,
> AF14)>;
> + /* LCD_DE */
> + slew-rate = <2>;
> + };
> + };
> +
> + i2c3_pins: i2c3-0 {
> + pins {
> + pinmux = <STM32_PINMUX('C', 9,
> AF4)>,
> + /* I2C3_SDA */
> + <STM32_PINMUX('A', 8,
> AF4)>;
> + /* I2C3_SCL */
> + bias-disable;
> + drive-open-drain;
> + slew-rate = <3>;
> + };
> + };
> +
> + spi5_pins: spi5-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('F', 7,
> AF5)>,
> + /* SPI5_CLK */
> + <STM32_PINMUX('F', 9,
> AF5)>;
> + /* SPI5_MOSI */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('F', 8,
> AF5)>;
> + /* SPI5_MISO */
> + bias-disable;
> + };
> + };
> +
> dcmi_pins: dcmi-0 {
> pins {
> pinmux = <STM32_PINMUX('A', 4,
> AF13)>, /* DCMI_HSYNC */
> diff --git a/arch/arm/boot/dts/stm32f429-disco.dts
> b/arch/arm/boot/dts/stm32f429-disco.dts
> index 30c0f67..55eed05 100644
> --- a/arch/arm/boot/dts/stm32f429-disco.dts
> +++ b/arch/arm/boot/dts/stm32f429-disco.dts
> @@ -49,6 +49,8 @@
> #include "stm32f429.dtsi"
> #include "stm32f429-pinctrl.dtsi"
> #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> model = "STMicroelectronics STM32F429i-DISCO board";
> @@ -98,6 +100,14 @@
> regulator-name = "vcc5_host1";
> regulator-always-on;
> };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> };
>
> &clk_hse {
> @@ -127,3 +137,81 @@
> pinctrl-names = "default";
> status = "okay";
> };
> +
> +<dc {
> + status = "okay";
> + pinctrl-0 = <<dc_pins_f429_disco>;
> + pinctrl-names = "default";
> +
> + port {
> + ltdc_out_rgb: endpoint {
> + remote-endpoint = <&panel_in_rgb>;
> + };
> + };
> +};
> +
> +&spi5 {
> + status = "okay";
> + pinctrl-0 = <&spi5_pins>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + cs-gpios = <&gpioc 1 GPIO_ACTIVE_LOW>,<&gpioc 2
> GPIO_ACTIVE_LOW>;
> + dmas = <&dma2 3 2 0x400 0x0>,
> + <&dma2 4 2 0x400 0x0>;
> + dma-names = "rx", "tx";
> + l3gd20: l3gd20@0 {
> + compatible = "st,l3gd20-gyro";
> + spi-max-frequency = <10000000>;
> + st,drdy-int-pin = <2>;
> + interrupt-parent = <&gpioa>;
> + interrupts = <1 IRQ_TYPE_EDGE_RISING>,
> + <2 IRQ_TYPE_EDGE_RISING>;
> + reg = <0>;
> + vddio = <®_3p3v>;
> + vdd = <®_3p3v>;
> + status = "okay";
> + };
> + display: display@1{
> + /* Connect panel-ilitek-9341 to ltdc */
> + compatible = "stm32f429-disco,ltdc-panel",
> "ilitek,ili9341";
> + reg = <1>;
> + spi-3wire;
> + spi-max-frequency = <10000000>;
> + dc-gpios = <&gpiod 13 0>;
> + port {
> + panel_in_rgb: endpoint {
> + remote-endpoint = <<dc_out_rgb>;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + status = "okay";
> +
> + touch: stmpe811@41 {
> + compatible = "st,stmpe811";
> + reg = <0x41>;
> + interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpioa>;
> + vio = <®_3p3v>;
> + vcc = <®_3p3v>;
> + status = "okay";
> +
> + stmpe_touchscreen {
> + compatible = "st,stmpe-ts";
> + st,sample-time = <4>;
> + st,mod-12b = <1>;
> + st,ref-sel = <0>;
> + st,adc-freq = <1>;
The above ADC related settings should go into the MFD device with
compatible "st,stmpe811". The use of those in touchscreen is deprecated.
Please check the bindings:
Documentation/devicetree/bindings/input/touchs
creen/stmpe.txt
Documentation/devicetree/bindings/mfd/stmpe.txt
Best Regards,
Philippe
Philippe,thanks. i will try it later, and move touch panel & gyro patchs out of this sets, after well tested, i'll resubmit it.
> + st,ave-ctrl = <1>;
> + st,touch-det-delay = <2>;
> + st,settling = <2>;
> + st,fraction-z = <7>;
> + st,i-drive = <1>;
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/stm32f429.dtsi
> b/arch/arm/boot/dts/stm32f429.dtsi
> index d777069..257b843 100644
> --- a/arch/arm/boot/dts/stm32f429.dtsi
> +++ b/arch/arm/boot/dts/stm32f429.dtsi
> @@ -402,6 +402,18 @@
> status = "disabled";
> };
>
> + i2c3: i2c@40005c00 {
> + compatible = "st,stm32f4-i2c";
> + reg = <0x40005c00 0x400>;
> + interrupts = <72>,
> + <73>;
> + resets = <&rcc STM32F4_APB1_RESET(I2C3)>;
> + clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C3)>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> dac: dac@40007400 {
> compatible = "st,stm32f4-dac-core";
> reg = <0x40007400 0x400>;
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
