Re: [PATCH 1/4] add dts node for drm panel driver ili9341 add dts i2c3 for stmpe touch add dts spi5 for gyro & ili9341

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

On Thu, 2020-04-30 at 17:43 +0800, dillon.minfei@xxxxxxxxx wrote:
> From: dillon min <dillon.minfei@xxxxxxxxx>
> 
> Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
> ---
>  .../bindings/display/panel/ilitek,ili9341.txt      | 42 +++++++++++
>  arch/arm/boot/dts/stm32f4-pinctrl.dtsi             | 79
> +++++++++++++++++++
>  arch/arm/boot/dts/stm32f429-disco.dts              | 88
> ++++++++++++++++++++++
>  arch/arm/boot/dts/stm32f429.dtsi                   | 12 +++
>  4 files changed, 221 insertions(+)
>  create mode 100644
> Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> 
> diff --git
> a/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> new file mode 100644
> index 0000000..f5a4e55
> --- /dev/null
> +++
> b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
> @@ -0,0 +1,42 @@
> +Ilitek ILI9341 TFT panel driver with SPI control bus
> +
> +This is a driver for 240x320 TFT panels, accepting a rgb input
> +streams that get adapted and scaled to the panel.
> +
> +Required properties:
> +  - compatible: "stm32f429-disco,ltdc-panel", "ilitek,ili9341"
> +    (full system-specific compatible is always required to look up
> configuration)
> +  - reg: address of the panel on the SPI bus
> +
> +Optional properties:
> +  - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
> +  - dc-gpios: a GPIO spec for the dc pin, see gpio/gpio.txt
> +
> +  The following optional properties only apply to RGB input mode:
> +
> +  - pixelclk-active: see display/panel/display-timing.txt
> +  - de-active: see display/panel/display-timing.txt
> +  - hsync-active: see display/panel/display-timing.txt
> +  - vsync-active: see display/panel/display-timing.txt
> +
> +The panel must obey the rules for a SPI slave device as specified in
> +spi/spi-bus.txt
> +
> +The device node can contain one 'port' child node with one child
> +'endpoint' node, according to the bindings defined in
> +media/video-interfaces.txt. This node should describe panel's video
> bus.
> +
> +Example:
> +
> +panel: display@0 {
> +	compatible = "stm32f429-disco,ltdc-panel", "ilitek,ili9341";
> +	reg = <0>;
> +	spi-3wire;
> +	spi-max-frequency = <10000000>;
> +	dc-gpios = <&gpiod 13 0>;
> +	port {
> +		panel_in: endpoint {
> +			remote-endpoint = <&display_out>;
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> index 392fa14..45b68f4 100644
> --- a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
> @@ -316,6 +316,85 @@
>  				};
>  			};
>  
> +			ltdc_pins_f429_disco: ltdc-1 {
> +				pins {
> +					pinmux = <STM32_PINMUX('C',
> 6,  AF14)>,
> +						/* LCD_HSYNC */
> +						 <STM32_PINMUX('A',
> 4,  AF14)>,
> +						 /* LCD_VSYNC */
> +						 <STM32_PINMUX('G',
> 7,  AF14)>,
> +						 /* LCD_CLK */
> +						 <STM32_PINMUX('C', 10,
> AF14)>,
> +						 /* LCD_R2 */
> +						 <STM32_PINMUX('B',
> 0,  AF9)>,
> +						 /* LCD_R3 */
> +						 <STM32_PINMUX('A', 11,
> AF14)>,
> +						 /* LCD_R4 */
> +						 <STM32_PINMUX('A', 12,
> AF14)>,
> +						 /* LCD_R5 */
> +						 <STM32_PINMUX('B',
> 1,  AF9)>,
> +						 /* LCD_R6*/
> +						 <STM32_PINMUX('G',
> 6,  AF14)>,
> +						 /* LCD_R7 */
> +						 <STM32_PINMUX('A',
> 6,  AF14)>,
> +						 /* LCD_G2 */
> +						 <STM32_PINMUX('G', 10,
> AF9)>,
> +						 /* LCD_G3 */
> +						 <STM32_PINMUX('B', 10,
> AF14)>,
> +						 /* LCD_G4 */
> +						 <STM32_PINMUX('D',
> 6,  AF14)>,
> +						 /* LCD_B2 */
> +						 <STM32_PINMUX('G', 11,
> AF14)>,
> +						 /* LCD_B3*/
> +						 <STM32_PINMUX('B', 11,
> AF14)>,
> +						 /* LCD_G5 */
> +						 <STM32_PINMUX('C',
> 7,  AF14)>,
> +						 /* LCD_G6 */
> +						 <STM32_PINMUX('D',
> 3,  AF14)>,
> +						 /* LCD_G7 */
> +						 <STM32_PINMUX('G', 12,
> AF9)>,
> +						 /* LCD_B4 */
> +						 <STM32_PINMUX('A',
> 3,  AF14)>,
> +						 /* LCD_B5 */
> +						 <STM32_PINMUX('B',
> 8,  AF14)>,
> +						 /* LCD_B6 */
> +						 <STM32_PINMUX('B',
> 9,  AF14)>,
> +						 /* LCD_B7 */
> +						 <STM32_PINMUX('F', 10,
> AF14)>;
> +						 /* LCD_DE */
> +					slew-rate = <2>;
> +				};
> +			};
> +
> +			i2c3_pins: i2c3-0 {
> +				pins {
> +					pinmux = <STM32_PINMUX('C', 9,
> AF4)>,
> +						/* I2C3_SDA */
> +						 <STM32_PINMUX('A', 8,
> AF4)>;
> +						/* I2C3_SCL */
> +					bias-disable;
> +					drive-open-drain;
> +					slew-rate = <3>;
> +				};
> +			};
> +
> +			spi5_pins: spi5-0 {
> +				pins1 {
> +					pinmux = <STM32_PINMUX('F', 7,
> AF5)>,
> +						/* SPI5_CLK */
> +						 <STM32_PINMUX('F', 9,
> AF5)>;
> +						/* SPI5_MOSI */
> +					bias-disable;
> +					drive-push-pull;
> +					slew-rate = <0>;
> +				};
> +				pins2 {
> +					pinmux = <STM32_PINMUX('F', 8,
> AF5)>;
> +						/* SPI5_MISO */
> +					bias-disable;
> +				};
> +			};
> +
>  			dcmi_pins: dcmi-0 {
>  				pins {
>  					pinmux = <STM32_PINMUX('A', 4,
> AF13)>, /* DCMI_HSYNC */
> diff --git a/arch/arm/boot/dts/stm32f429-disco.dts
> b/arch/arm/boot/dts/stm32f429-disco.dts
> index 30c0f67..55eed05 100644
> --- a/arch/arm/boot/dts/stm32f429-disco.dts
> +++ b/arch/arm/boot/dts/stm32f429-disco.dts
> @@ -49,6 +49,8 @@
>  #include "stm32f429.dtsi"
>  #include "stm32f429-pinctrl.dtsi"
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
>  
>  / {
>  	model = "STMicroelectronics STM32F429i-DISCO board";
> @@ -98,6 +100,14 @@
>  		regulator-name = "vcc5_host1";
>  		regulator-always-on;
>  	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +	};
>  };
>  
>  &clk_hse {
> @@ -127,3 +137,81 @@
>  	pinctrl-names = "default";
>  	status = "okay";
>  };
> +
> +&ltdc {
> +	status = "okay";
> +	pinctrl-0 = <&ltdc_pins_f429_disco>;
> +	pinctrl-names = "default";
> +
> +	port {
> +		ltdc_out_rgb: endpoint {
> +			remote-endpoint = <&panel_in_rgb>;
> +		};
> +	};
> +};
> +
> +&spi5 {
> +	status = "okay";
> +	pinctrl-0 = <&spi5_pins>;
> +	pinctrl-names = "default";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	cs-gpios = <&gpioc 1 GPIO_ACTIVE_LOW>,<&gpioc 2
> GPIO_ACTIVE_LOW>;
> +	dmas = <&dma2 3 2 0x400 0x0>,
> +	       <&dma2 4 2 0x400 0x0>;
> +	dma-names = "rx", "tx";
> +	l3gd20: l3gd20@0 {
> +		compatible = "st,l3gd20-gyro";
> +		spi-max-frequency = <10000000>;
> +		st,drdy-int-pin = <2>;
> +		interrupt-parent = <&gpioa>;
> +		interrupts = <1 IRQ_TYPE_EDGE_RISING>,
> +				<2 IRQ_TYPE_EDGE_RISING>;
> +		reg = <0>;
> +		vddio = <&reg_3p3v>;
> +		vdd = <&reg_3p3v>;
> +		status = "okay";
> +	};
> +	display: display@1{
> +		/* Connect panel-ilitek-9341 to ltdc */
> +		compatible = "stm32f429-disco,ltdc-panel",
> "ilitek,ili9341";
> +		reg = <1>;
> +		spi-3wire;
> +		spi-max-frequency = <10000000>;
> +		dc-gpios = <&gpiod 13 0>;
> +		port {
> +			panel_in_rgb: endpoint {
> +			remote-endpoint = <&ltdc_out_rgb>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3_pins>;
> +	status = "okay";
> +
> +	touch: stmpe811@41 {
> +		compatible = "st,stmpe811";
> +		reg = <0x41>;
> +		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpioa>;
> +		vio = <&reg_3p3v>;
> +		vcc = <&reg_3p3v>;
> +		status = "okay";
> +
> +		stmpe_touchscreen {
> +			compatible = "st,stmpe-ts";
> +			st,sample-time = <4>;
> +			st,mod-12b = <1>;
> +			st,ref-sel = <0>;
> +			st,adc-freq = <1>;

The above ADC related settings should go into the MFD device with
compatible "st,stmpe811". The use of those in touchscreen is deprecated.

Please check the bindings:
Documentation/devicetree/bindings/input/touchs
creen/stmpe.txt
Documentation/devicetree/bindings/mfd/stmpe.txt

Best Regards,
Philippe

> +			st,ave-ctrl = <1>;
> +			st,touch-det-delay = <2>;
> +			st,settling = <2>;
> +			st,fraction-z = <7>;
> +			st,i-drive = <1>;
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/stm32f429.dtsi
> b/arch/arm/boot/dts/stm32f429.dtsi
> index d777069..257b843 100644
> --- a/arch/arm/boot/dts/stm32f429.dtsi
> +++ b/arch/arm/boot/dts/stm32f429.dtsi
> @@ -402,6 +402,18 @@
>  			status = "disabled";
>  		};
>  
> +		i2c3: i2c@40005c00 {
> +			compatible = "st,stm32f4-i2c";
> +			reg = <0x40005c00 0x400>;
> +			interrupts = <72>,
> +				     <73>;
> +			resets = <&rcc STM32F4_APB1_RESET(I2C3)>;
> +			clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C3)>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
>  		dac: dac@40007400 {
>  			compatible = "st,stm32f4-dac-core";
>  			reg = <0x40007400 0x400>;
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux