Hi, On Wed, Apr 15, 2020 at 1:31 PM Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote: > > Hi Douglas, > > Thank you for the patch. > > On Wed, Apr 15, 2020 at 08:48:39AM -0700, Douglas Anderson wrote: > > This moves the bindings over, based a lot on toshiba,tc358768.yaml. > > Unless there's someone known to be better, I've set the maintainer in > > the yaml as the first person to submit bindings. > > You can also add your name ;-) Sure, though I spend most of my days flitting from subsystem to subsystem, always a noob everywhere I go. I'm not sure I'd really be qualified. ;-) If you want, I can add myself though I'd rather not be solely responsible for this file since I probably won't be the best at keeping track of it... I left this as-is for v2 but can change it if you want. > > Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx> > > --- > > > > .../bindings/display/bridge/ti,sn65dsi86.txt | 87 -------- > > .../bindings/display/bridge/ti,sn65dsi86.yaml | 188 ++++++++++++++++++ > > 2 files changed, 188 insertions(+), 87 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > deleted file mode 100644 > > index 8ec4a7f2623a..000000000000 > > --- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > +++ /dev/null > > @@ -1,87 +0,0 @@ > > -SN65DSI86 DSI to eDP bridge chip > > --------------------------------- > > - > > -This is the binding for Texas Instruments SN65DSI86 bridge. > > -http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > > - > > -Required properties: > > -- compatible: Must be "ti,sn65dsi86" > > -- reg: i2c address of the chip, 0x2d as per datasheet > > -- enable-gpios: gpio specification for bridge_en pin (active high) > > - > > -- vccio-supply: A 1.8V supply that powers up the digital IOs. > > -- vpll-supply: A 1.8V supply that powers up the displayport PLL. > > -- vcca-supply: A 1.2V supply that powers up the analog circuits. > > -- vcc-supply: A 1.2V supply that powers up the digital core. > > - > > -Optional properties: > > -- interrupts-extended: Specifier for the SN65DSI86 interrupt line. > > - > > -- gpio-controller: Marks the device has a GPIO controller. > > -- #gpio-cells : Should be two. The first cell is the pin number and > > - the second cell is used to specify flags. > > - See ../../gpio/gpio.txt for more information. > > -- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of > > - the cell formats. > > - > > -- clock-names: should be "refclk" > > -- clocks: Specification for input reference clock. The reference > > - clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > > - > > -- data-lanes: See ../../media/video-interface.txt > > -- lane-polarities: See ../../media/video-interface.txt > > - > > -- suspend-gpios: specification for GPIO1 pin on bridge (active low) > > Where has suspend-gpios gone ? :-) Oops. Added it back. > > - > > -Required nodes: > > -This device has two video ports. Their connections are modelled using the > > -OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > - > > -- Video port 0 for DSI input > > -- Video port 1 for eDP output > > - > > -Example > > -------- > > - > > -edp-bridge@2d { > > - compatible = "ti,sn65dsi86"; > > - #address-cells = <1>; > > - #size-cells = <0>; > > - reg = <0x2d>; > > - > > - enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; > > - suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; > > - > > - interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; > > - > > - vccio-supply = <&pm8916_l17>; > > - vcca-supply = <&pm8916_l6>; > > - vpll-supply = <&pm8916_l17>; > > - vcc-supply = <&pm8916_l6>; > > - > > - clock-names = "refclk"; > > - clocks = <&input_refclk>; > > - > > - ports { > > - #address-cells = <1>; > > - #size-cells = <0>; > > - > > - port@0 { > > - reg = <0>; > > - > > - edp_bridge_in: endpoint { > > - remote-endpoint = <&dsi_out>; > > - }; > > - }; > > - > > - port@1 { > > - reg = <1>; > > - > > - edp_bridge_out: endpoint { > > - data-lanes = <2 1 3 0>; > > - lane-polarities = <0 1 0 1>; > > - remote-endpoint = <&edp_panel_in>; > > - }; > > - }; > > - }; > > -} > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml > > new file mode 100644 > > index 000000000000..8cacc6db33a9 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml > > @@ -0,0 +1,188 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi86.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: SN65DSI86 DSI to eDP bridge chip > > + > > +maintainers: > > + - Sandeep Panda <spanda@xxxxxxxxxxxxxx> > > + > > +description: | > > + The Texas Instruments SN65DSI86 bridge takes MIPI DSI in and outputs eDP. > > + http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > > + > > +properties: > > + compatible: > > + const: ti,sn65dsi86 > > + > > + reg: > > + const: 0x2d > > + > > + enable-gpios: > > + maxItems: 1 > > + description: GPIO specification for bridge_en pin (active high). > > + > > + vccio-supply: > > + description: A 1.8V supply that powers up the digital IOs. > > + > > + vpll-supply: > > + description: A 1.8V supply that powers up the DisplayPort PLL. > > + > > + vcca-supply: > > + description: A 1.2V supply that powers up the analog circuits. > > + > > + vcc-supply: > > + description: A 1.2V supply that powers up the digital core. > > + > > + interrupts: > > + maxItems: 1 > > + > > + clocks: > > + maxItems: 1 > > + description: > > + Specification for input reference clock. The reference clock rate must > > + be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > > + > > + clock-names: > > + const: refclk > > + > > + gpio-controller: true > > + '#gpio-cells': > > + const: 2 > > + description: > > + First cell is pin number, second cell is flags. GPIO pin numbers are > > + 1-based to match the datasheet. See ../../gpio/gpio.txt for more > > + information. > > + > > + '#pwm-cells': > > + const: 1 > > + description: See ../../pwm/pwm.yaml for description of the cell formats. > > + > > + data-lanes: > > Should this have > > minItems: 1 > maxItems: 4 > items: > enum: > - 0 > - 1 > - 2 > - 3 Interestingly this seemed to be at totally the wrong location in the old ".txt" file and in my v1. I moved it to the right place now by making sure I put the old example back in, not just the example of what's currently in the tree. > > + description: See ../../media/video-interface.txt > > + > > + lane-polarities: > > + description: See ../../media/video-interface.txt > > And something similar here, > > minItems: 1 > maxItems: 4 > items: > enum: > - 0 > - 1 > uniqueItems: false > > I'm not entirely sure where uniqueItems should be placed. I left this out of v2. "uniqueItems: false" appears to be the default so it would only be needed if you were trying to override someone who had already made this "true". I tested this by setting it to true and seeing the error, then removing the set to true and seeing the error gone. > I'm also not > sure how to specify that both data-lanes and lane-polarities need to > have the same number of items, maybe > > dependencies: > data-lanes: [lane-polarities] The opposite of that is interesting, that is: dependencies: data-lanes: [lane-polarities] ...that seems to say that specifying "lane-polarities" without "data-lanes" is an error. ...but that doesn't specify that data-lanes and lane-polarities need to have the same number of items. If someone wants to provide the syntax I'm happy to add it, otherwise it feels like it could be something to improve in the future. In general I haven't seen people get to this level of detail in yaml. > > + > > + ports: > > + type: object > > + > > + properties: > > + "#address-cells": > > + const: 1 > > + > > + "#size-cells": > > + const: 0 > > + > > + port@0: > > + type: object > > + additionalProperties: false > > + > > + description: > > + Video port for MIPI DSI input > > + > > + properties: > > + reg: > > + const: 0 > > + > > + patternProperties: > > + endpoint: > > If there's a single endpoint, you don't need patternProperties, it can > be specified in properties. Done. _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
