This moves the bindings over, based a lot on toshiba,tc358768.yaml. Unless there's someone known to be better, I've set the maintainer in the yaml as the first person to submit bindings. Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 87 -------- .../bindings/display/bridge/ti,sn65dsi86.yaml | 188 ++++++++++++++++++ 2 files changed, 188 insertions(+), 87 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt deleted file mode 100644 index 8ec4a7f2623a..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt +++ /dev/null @@ -1,87 +0,0 @@ -SN65DSI86 DSI to eDP bridge chip --------------------------------- - -This is the binding for Texas Instruments SN65DSI86 bridge. -http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf - -Required properties: -- compatible: Must be "ti,sn65dsi86" -- reg: i2c address of the chip, 0x2d as per datasheet -- enable-gpios: gpio specification for bridge_en pin (active high) - -- vccio-supply: A 1.8V supply that powers up the digital IOs. -- vpll-supply: A 1.8V supply that powers up the displayport PLL. -- vcca-supply: A 1.2V supply that powers up the analog circuits. -- vcc-supply: A 1.2V supply that powers up the digital core. - -Optional properties: -- interrupts-extended: Specifier for the SN65DSI86 interrupt line. - -- gpio-controller: Marks the device has a GPIO controller. -- #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify flags. - See ../../gpio/gpio.txt for more information. -- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of - the cell formats. - -- clock-names: should be "refclk" -- clocks: Specification for input reference clock. The reference - clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. - -- data-lanes: See ../../media/video-interface.txt -- lane-polarities: See ../../media/video-interface.txt - -- suspend-gpios: specification for GPIO1 pin on bridge (active low) - -Required nodes: -This device has two video ports. Their connections are modelled using the -OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. - -- Video port 0 for DSI input -- Video port 1 for eDP output - -Example -------- - -edp-bridge@2d { - compatible = "ti,sn65dsi86"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x2d>; - - enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; - suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; - - interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; - - vccio-supply = <&pm8916_l17>; - vcca-supply = <&pm8916_l6>; - vpll-supply = <&pm8916_l17>; - vcc-supply = <&pm8916_l6>; - - clock-names = "refclk"; - clocks = <&input_refclk>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - edp_bridge_in: endpoint { - remote-endpoint = <&dsi_out>; - }; - }; - - port@1 { - reg = <1>; - - edp_bridge_out: endpoint { - data-lanes = <2 1 3 0>; - lane-polarities = <0 1 0 1>; - remote-endpoint = <&edp_panel_in>; - }; - }; - }; -} diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml new file mode 100644 index 000000000000..8cacc6db33a9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi86.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SN65DSI86 DSI to eDP bridge chip + +maintainers: + - Sandeep Panda <spanda@xxxxxxxxxxxxxx> + +description: | + The Texas Instruments SN65DSI86 bridge takes MIPI DSI in and outputs eDP. + http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +properties: + compatible: + const: ti,sn65dsi86 + + reg: + const: 0x2d + + enable-gpios: + maxItems: 1 + description: GPIO specification for bridge_en pin (active high). + + vccio-supply: + description: A 1.8V supply that powers up the digital IOs. + + vpll-supply: + description: A 1.8V supply that powers up the DisplayPort PLL. + + vcca-supply: + description: A 1.2V supply that powers up the analog circuits. + + vcc-supply: + description: A 1.2V supply that powers up the digital core. + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: + Specification for input reference clock. The reference clock rate must + be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. + + clock-names: + const: refclk + + gpio-controller: true + '#gpio-cells': + const: 2 + description: + First cell is pin number, second cell is flags. GPIO pin numbers are + 1-based to match the datasheet. See ../../gpio/gpio.txt for more + information. + + '#pwm-cells': + const: 1 + description: See ../../pwm/pwm.yaml for description of the cell formats. + + data-lanes: + description: See ../../media/video-interface.txt + + lane-polarities: + description: See ../../media/video-interface.txt + + ports: + type: object + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + port@0: + type: object + additionalProperties: false + + description: + Video port for MIPI DSI input + + properties: + reg: + const: 0 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + remote-endpoint: true + + required: + - reg + + port@1: + type: object + additionalProperties: false + + description: + Video port for eDP output (panel or connector). + + properties: + reg: + const: 1 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + remote-endpoint: true + + required: + - reg + + required: + - "#address-cells" + - "#size-cells" + - port@0 + - port@1 + +required: + - compatible + - reg + - enable-gpios + - vccio-supply + - vpll-supply + - vcca-supply + - vcc-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c1 { + #address-cells = <1>; + #size-cells = <0>; + + bridge@2d { + compatible = "ti,sn65dsi86"; + reg = <0x2d>; + + interrupt-parent = <&tlmm>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; + + vpll-supply = <&src_pp1800_s4a>; + vccio-supply = <&src_pp1800_s4a>; + vcca-supply = <&src_pp1200_l2a>; + vcc-supply = <&src_pp1200_l2a>; + + clocks = <&rpmhcc RPMH_LN_BB_CLK2>; + clock-names = "refclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + }; + }; + -- 2.26.0.110.g2183baf09c-goog _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
