On Mon, 2020-02-24 at 16:46 +0800, CK Hu wrote: > Hi, Jitao: > > On Fri, 2020-02-21 at 19:28 +0800, Jitao Shi wrote: > > Add decriptions about supported chips, including MT2701 & MT8173 & > > mt8183 > > > > 1. Add more chips support. ex. MT2701 & MT8173 & MT8183 > > 2. Add property "dpi_pin_mode_swap" and "pinctrl-names" gpio mode dpi mode and > > gpio oupput-low to avoid leakage current. > > 3. Add property "dpi_dual_edge" to config the dpi pin output mode dual edge or > > single edge sample data. > > > > Signed-off-by: Jitao Shi <jitao.shi@xxxxxxxxxxxx> > > --- > > .../bindings/display/mediatek/mediatek,dpi.txt | 11 +++++++++++ > > 1 file changed, 11 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt > > index b6a7e7397b8b..cd6a1469c8b7 100644 > > --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt > > +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt > > @@ -7,6 +7,7 @@ output bus. > > > > Required properties: > > - compatible: "mediatek,<chip>-dpi" > > + the supported chips are mt2701 , mt8173 and mt8183. > > - reg: Physical base address and length of the controller's registers > > - interrupts: The interrupt signal from the function block. > > - clocks: device clocks > > @@ -16,6 +17,11 @@ Required properties: > > Documentation/devicetree/bindings/graph.txt. This port should be connected > > to the input port of an attached HDMI or LVDS encoder chip. > > > > +Optional properties: > > +- dpi_pin_mode_swap: Swap the pin mode between dpi mode and gpio mode. > > +- pinctrl-names: Contain "gpiomode" and "dpimode". > > +- dpi_dual_edge: Control the RGB 24bit data on 12 pins or 24 pins. > > I've find that in [1], there are already a property of "pclk-sample" > which like this, but it only have rising (1) or falling (0) status. Does > that property describe the same thing with this property? If they are > the same, I think you should add new state, dual (2), for "pclk-sample". > > [1] > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/media/video-interfaces.txt?h=v5.6-rc3 > > Regards, > CK > pclk-sample has two properties rising or falling. It means to sample on rising or falling edge. But, dpi_dual_edge means to sample on both rising and falling edge. Best Regards Jitao > > + > > Example: > > > > dpi0: dpi@1401d000 { > > @@ -26,6 +32,11 @@ dpi0: dpi@1401d000 { > > <&mmsys CLK_MM_DPI_ENGINE>, > > <&apmixedsys CLK_APMIXED_TVDPLL>; > > clock-names = "pixel", "engine", "pll"; > > + dpi_dual_edge; > > + dpi_pin_mode_swap; > > + pinctrl-names = "gpiomode", "dpimode"; > > + pinctrl-0 = <&dpi_pin_gpio>; > > + pinctrl-1 = <&dpi_pin_func>; > > > > port { > > dpi0_out: endpoint { > > _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
