Re: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi supported chips

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi, Jitao:

On Fri, 2020-02-21 at 19:28 +0800, Jitao Shi wrote:
> Add decriptions about supported chips, including MT2701 & MT8173 &
> mt8183
> 
> 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> 2. Add property "dpi_pin_mode_swap" and "pinctrl-names" gpio mode dpi mode and
>    gpio oupput-low to avoid leakage current.
> 3. Add property "dpi_dual_edge" to config the dpi pin output mode dual edge or
>    single edge sample data.
> 
> Signed-off-by: Jitao Shi <jitao.shi@xxxxxxxxxxxx>
> ---
>  .../bindings/display/mediatek/mediatek,dpi.txt        | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index b6a7e7397b8b..cd6a1469c8b7 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -7,6 +7,7 @@ output bus.
>  
>  Required properties:
>  - compatible: "mediatek,<chip>-dpi"
> +  the supported chips are mt2701 , mt8173 and mt8183.
>  - reg: Physical base address and length of the controller's registers
>  - interrupts: The interrupt signal from the function block.
>  - clocks: device clocks
> @@ -16,6 +17,11 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- dpi_pin_mode_swap: Swap the pin mode between dpi mode and gpio mode.
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +- dpi_dual_edge: Control the RGB 24bit data on 12 pins or 24 pins.

I've find that in [1], there are already a property of "pclk-sample"
which like this, but it only have rising (1) or falling (0) status. Does
that property describe the same thing with this property? If they are
the same, I think you should add new state, dual (2), for "pclk-sample".

[1]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/media/video-interfaces.txt?h=v5.6-rc3

Regards,
CK

> +
>  Example:
>  
>  dpi0: dpi@1401d000 {
> @@ -26,6 +32,11 @@ dpi0: dpi@1401d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	dpi_dual_edge;
> +	dpi_pin_mode_swap;
> +	pinctrl-names = "gpiomode", "dpimode";
> +	pinctrl-0 = <&dpi_pin_gpio>;
> +	pinctrl-1 = <&dpi_pin_func>;
>  
>  	port {
>  		dpi0_out: endpoint {

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux