Hi, Yongqiang:
On Thu, 2020-01-02 at 14:21 +0800, Yongqiang Niu wrote:
> On Thu, 2020-01-02 at 14:02 +0800, CK Hu wrote:
> > Hi, Yongqiang:
> >
> > On Thu, 2020-01-02 at 13:39 +0800, Yongqiang Niu wrote:
> > > On Thu, 2020-01-02 at 13:03 +0800, CK Hu wrote:
> > > > Hi, Yongqiang:
> > > >
> > > > On Thu, 2020-01-02 at 12:00 +0800, Yongqiang Niu wrote:
> > > > > move dsi/dpi select input into mtk_ddp_sel_in
> > > > >
> > > > > Signed-off-by: Yongqiang Niu <yongqiang.niu@xxxxxxxxxxxx>
> > > > > ---
> > > > > drivers/gpu/drm/mediatek/mtk_drm_ddp.c | 10 ++++++----
> > > > > 1 file changed, 6 insertions(+), 4 deletions(-)
> > > > >
> > > > > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp.c b/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > > index 39700b9..91c9b19 100644
> > > > > --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > > +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > > @@ -376,6 +376,12 @@ static unsigned int mtk_ddp_sel_in(enum mtk_ddp_comp_id cur,
> > > > > } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DSI0) {
> > > > > *addr = DISP_REG_CONFIG_DSI_SEL;
> > > > > value = DSI_SEL_IN_BLS;
> > > > > + } else if (cur == DDP_COMPONENT_RDMA1 && next == DDP_COMPONENT_DSI0) {
> > > > > + *addr = DISP_REG_CONFIG_DSI_SEL;
> > > > > + value = DSI_SEL_IN_RDMA;
> > > >
> > > > In original code, this is set when cur == DDP_COMPONENT_BLS and next ==
> > > > DDP_COMPONENT_DPI0. Why do you change the condition?
> > > >
> > > > Regards,
> > > > CK
> > >
> > > if bls connect with dpi0, rdma1 should connect with dsi0, the condition
> > > is same with before.
> >
> > You suggest that two crtcs are both enabled. If only one crtc is
> > enabled, just one of these two would be set.
> >
> > Regards,
> > CK
>
> OK, i will modify like this
> else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
> *addr = DISP_REG_CONFIG_DSI_SEL;
> value = DPI_SEL_IN_RDMA;
> }
> in mtk_ddp_sel_in.
>
> don't set DISP_REG_CONFIG_DPI_SEL to DPI_SEL_IN_BLS anymore, because
> DPI_SEL_IN_BLS is zero, it is same with hardware default setting.
In Bibby's case, there is only the path from BLS to DPI0 and has no path
from RDMA1 to DSI0, but it need to set these two register. Maybe its
setting is just for some SoC, so you may use the compatible name to
judge how to set this two register.
Regards,
CK
> >
> > > >
> > > > > + } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
> > > > > + *addr = DISP_REG_CONFIG_DPI_SEL;
> > > > > + value = DPI_SEL_IN_BLS;
> > > > > } else {
> > > > > value = 0;
> > > > > }
> > > > > @@ -393,10 +399,6 @@ static void mtk_ddp_sout_sel(struct regmap *config_regs,
> > > > > } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
> > > > > regmap_write(config_regs, DISP_REG_CONFIG_OUT_SEL,
> > > > > BLS_TO_DPI_RDMA1_TO_DSI);
> > > > > - regmap_write(config_regs, DISP_REG_CONFIG_DSI_SEL,
> > > > > - DSI_SEL_IN_RDMA);
> > > > > - regmap_write(config_regs, DISP_REG_CONFIG_DPI_SEL,
> > > > > - DPI_SEL_IN_BLS);
> > > > > }
> > > > > }
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
