On Thu, 2020-01-02 at 14:02 +0800, CK Hu wrote:
> Hi, Yongqiang:
>
> On Thu, 2020-01-02 at 13:39 +0800, Yongqiang Niu wrote:
> > On Thu, 2020-01-02 at 13:03 +0800, CK Hu wrote:
> > > Hi, Yongqiang:
> > >
> > > On Thu, 2020-01-02 at 12:00 +0800, Yongqiang Niu wrote:
> > > > move dsi/dpi select input into mtk_ddp_sel_in
> > > >
> > > > Signed-off-by: Yongqiang Niu <yongqiang.niu@xxxxxxxxxxxx>
> > > > ---
> > > > drivers/gpu/drm/mediatek/mtk_drm_ddp.c | 10 ++++++----
> > > > 1 file changed, 6 insertions(+), 4 deletions(-)
> > > >
> > > > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp.c b/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > index 39700b9..91c9b19 100644
> > > > --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp.c
> > > > @@ -376,6 +376,12 @@ static unsigned int mtk_ddp_sel_in(enum mtk_ddp_comp_id cur,
> > > > } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DSI0) {
> > > > *addr = DISP_REG_CONFIG_DSI_SEL;
> > > > value = DSI_SEL_IN_BLS;
> > > > + } else if (cur == DDP_COMPONENT_RDMA1 && next == DDP_COMPONENT_DSI0) {
> > > > + *addr = DISP_REG_CONFIG_DSI_SEL;
> > > > + value = DSI_SEL_IN_RDMA;
> > >
> > > In original code, this is set when cur == DDP_COMPONENT_BLS and next ==
> > > DDP_COMPONENT_DPI0. Why do you change the condition?
> > >
> > > Regards,
> > > CK
> >
> > if bls connect with dpi0, rdma1 should connect with dsi0, the condition
> > is same with before.
>
> You suggest that two crtcs are both enabled. If only one crtc is
> enabled, just one of these two would be set.
>
> Regards,
> CK
OK, i will modify like this
else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
*addr = DISP_REG_CONFIG_DSI_SEL;
value = DPI_SEL_IN_RDMA;
}
in mtk_ddp_sel_in.
don't set DISP_REG_CONFIG_DPI_SEL to DPI_SEL_IN_BLS anymore, because
DPI_SEL_IN_BLS is zero, it is same with hardware default setting.
>
> > >
> > > > + } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
> > > > + *addr = DISP_REG_CONFIG_DPI_SEL;
> > > > + value = DPI_SEL_IN_BLS;
> > > > } else {
> > > > value = 0;
> > > > }
> > > > @@ -393,10 +399,6 @@ static void mtk_ddp_sout_sel(struct regmap *config_regs,
> > > > } else if (cur == DDP_COMPONENT_BLS && next == DDP_COMPONENT_DPI0) {
> > > > regmap_write(config_regs, DISP_REG_CONFIG_OUT_SEL,
> > > > BLS_TO_DPI_RDMA1_TO_DSI);
> > > > - regmap_write(config_regs, DISP_REG_CONFIG_DSI_SEL,
> > > > - DSI_SEL_IN_RDMA);
> > > > - regmap_write(config_regs, DISP_REG_CONFIG_DPI_SEL,
> > > > - DPI_SEL_IN_BLS);
> > > > }
> > > > }
> > > >
> > >
> > >
> >
> >
>
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
