On Thu, Aug 15, 2019 at 11:14:17AM +0000, Wen He wrote:
>
>
> > -----Original Message-----
> > From: Liviu Dudau <liviu.dudau@xxxxxxx>
> > Sent: 2019年7月22日 17:33
> > To: Wen He <wen.he_1@xxxxxxx>
> > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > brian.starkey@xxxxxxx; airlied@xxxxxxxx; daniel@xxxxxxxx; Leo Li
> > <leoyang.li@xxxxxxx>
> > Subject: Re: [EXT] Re: [v2 1/3] drm/arm/mali-dp: Add display QoS interface
> > configuration for Mali DP500
> >
> > Caution: EXT Email
> >
> > On Mon, Jul 22, 2019 at 02:12:08AM +0000, Wen He wrote:
> > >
> > >
> > > > -----Original Message-----
> > > > From: Liviu Dudau <liviu.dudau@xxxxxxx>
> > > > Sent: 2019年7月19日 19:46
> > > > To: Wen He <wen.he_1@xxxxxxx>
> > > > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > > > brian.starkey@xxxxxxx; airlied@xxxxxxxx; daniel@xxxxxxxx; Leo Li
> > > > <leoyang.li@xxxxxxx>
> > > > Subject: [EXT] Re: [v2 1/3] drm/arm/mali-dp: Add display QoS
> > > > interface configuration for Mali DP500
> > > >
> > > > Caution: EXT Email
> > > >
> > > > On Fri, Jul 19, 2019 at 05:54:45PM +0800, Wen He wrote:
> > > > > Configure the display Quality of service (QoS) levels priority if
> > > > > the optional property node "arm,malidp-aqros-value" is defined in DTS
> > file.
> > > > >
> > > > > QoS signaling using AQROS and AWQOS AXI interface signals, the
> > > > > AQROS is driven from the "RQOS" register, so needed to program the
> > > > > RQOS register to avoid the 4k resolution flicker issue on the LS1028A
> > platform.
> > > > >
> > > > > Signed-off-by: Wen He <wen.he_1@xxxxxxx>
> > > > > ---
> > > > > change in v2:
> > > > > - modify some content based on feedback from maintainers
> > > > >
> > > > > drivers/gpu/drm/arm/malidp_drv.c | 6 ++++++
> > > > > drivers/gpu/drm/arm/malidp_hw.c | 13 +++++++++++++
> > > > > drivers/gpu/drm/arm/malidp_hw.h | 3 +++
> > > > > drivers/gpu/drm/arm/malidp_regs.h | 10 ++++++++++
> > > > > 4 files changed, 32 insertions(+)
> > > > >
> > > > > diff --git a/drivers/gpu/drm/arm/malidp_drv.c
> > > > > b/drivers/gpu/drm/arm/malidp_drv.c
> > > > > index f25ec4382277..61c49a0668a7 100644
> > > > > --- a/drivers/gpu/drm/arm/malidp_drv.c
> > > > > +++ b/drivers/gpu/drm/arm/malidp_drv.c
> > > > > @@ -818,6 +818,12 @@ static int malidp_bind(struct device *dev)
> > > > >
> > > > > malidp->core_id = version;
> > > > >
> > > > > + ret = of_property_read_u32(dev->of_node,
> > > > > + "arm,malidp-arqos-value",
> > > > > + &hwdev->arqos_value);
> > > > > + if (ret)
> > > > > + hwdev->arqos_value = 0x0;
> > > >
> > > > Is zero the default value that you want? I thought it was 0x00010001.
> > >
> > > Actually, the register default value always is 0x00010001(can be found in RM
> > document).
> >
> > Exactly, but with your code you are overwriting it to 0 if the DT doesn't have
> > the arm,malidp-arqos-value property.
> >
> > >
> > > >
> > > > > +
> > > > > /* set the number of lines used for output of RGB data */
> > > > > ret = of_property_read_u8_array(dev->of_node,
> > > > >
> > > > > "arm,malidp-output-port-lines", diff --git
> > > > > a/drivers/gpu/drm/arm/malidp_hw.c
> > > > > b/drivers/gpu/drm/arm/malidp_hw.c index 50af399d7f6f..323683b1e9f7
> > > > > 100644
> > > > > --- a/drivers/gpu/drm/arm/malidp_hw.c
> > > > > +++ b/drivers/gpu/drm/arm/malidp_hw.c
> > > > > @@ -374,6 +374,19 @@ static void malidp500_modeset(struct
> > > > malidp_hw_device *hwdev, struct videomode *
> > > > > malidp_hw_setbits(hwdev, MALIDP_DISP_FUNC_ILACED,
> > > > MALIDP_DE_DISPLAY_FUNC);
> > > > > else
> > > > > malidp_hw_clearbits(hwdev,
> > MALIDP_DISP_FUNC_ILACED,
> > > > > MALIDP_DE_DISPLAY_FUNC);
> > > > > +
> > > > > + /*
> > > > > + * Program the RQoS register to avoid 4k resolution flicker
> > > > > + * on the LS1028A.
> > > > > + */
> > > > > + if (hwdev->arqos_value) {
> > > > > + val = hwdev->arqos_value;
> > > > > +
> > > > > + if (mode->pixelclock == 594000000)
> > > >
> > > > If I remember correctly, you declare the pixelclocks in the device
> > > > tree, so I wonder if this is needed here. We should just set what
> > > > value was in the DT regardless of the pixelclock, and then you
> > > > manipulate the DT to choose one of your fixed resolutions and also set the
> > QoS value.
> > >
> > > Yes, you remember correctly, but
> > > 1. declare the pixelclocks in the device tree.
> > > About this, I was hoping to discuss it with you. I want to implement
> > > another patch that just declare 27MHz reference clock in the device
> > > tree and add a fake clock subsystem to enable/display prepare to set PLL. I
> > am thinking what to do next.
> > > As I remember, I sent out a patch that "Disable checking for required
> > > pixel clock", I think should be cancel it.
> > >
> > > 2. declare the fixed resolutions list in DTS.
> > > Yes, Although I put four resolutions for supported list in DTS file,
> > > but this just a workaround that If not enable EDID OR EDID is not
> > > available. Once EDID is enabled, these resolutions list declare will
> > > be remove in DTS. so we can't use it as a condition to set the QoS value.
> >
> > 3. Actually enable the clock provider. I've had a look at the public
> > documentation and it looks like the the pixelclock is provided by an IDT
> > VersaClock 5 generator, for which there is a kernel driver. I've started playing
> > with it but got pulled back by other more immediate tasks.
> >
> > Anyway, what I was trying to hint was that putting in the code the exact
> > pixelclock value might not be the best thing. In my view, pixelclock reflects the
> > need for a certain bandwidth, with is usually a product of output (number of
> > pixels) and refresh frequency. I'm guessing going above 4k@60 will also trigger
> > the flicker, but with your patch we will not react correctly.
> >
> > Best regards,
> > Liviu
> >
>
> Hmm.. I've already written the pixel clock provider driver of the LS1028A and upstreamed..
> So more resolutions will be support on LS1028A.
> Thank you for the comments that which made me determined to get this done.
>
> For this change, I would be remove this condition "if (mode->pixelclock == 594000000)"
> And apply this change for all resolutions on LS1028A.
>
> How do you think?
Hi Wen,
Sorry, I was away on sabbatical until now.
Not sure if I got your message right: do you want to apply the RQOS value regardless
of the resolution (but only if defined to a non-zero value in the DTS)? If so, then
I'm fine with that idea. Can you send a refreshed patch?
Best regards,
Liviu
>
> Best Regards,
> Wen
> >
> > >
> > > Best Regards,
> > > Wen
> > >
> > > >
> > > > Best regards,
> > > > Liviu
> > > >
> > > > > + malidp_hw_setbits(hwdev, val,
> > > > MALIDP500_RQOS_QUALITY);
> > > > > + else
> > > > > + malidp_hw_clearbits(hwdev, val,
> > > > MALIDP500_RQOS_QUALITY);
> > > > > + }
> > > > > }
> > > > >
> > > > > int malidp_format_get_bpp(u32 fmt) diff --git
> > > > > a/drivers/gpu/drm/arm/malidp_hw.h
> > > > > b/drivers/gpu/drm/arm/malidp_hw.h index
> > 968a65eed371..e4c36bc90bda
> > > > > 100644
> > > > > --- a/drivers/gpu/drm/arm/malidp_hw.h
> > > > > +++ b/drivers/gpu/drm/arm/malidp_hw.h
> > > > > @@ -251,6 +251,9 @@ struct malidp_hw_device {
> > > > >
> > > > > /* size of memory used for rotating layers, up to two banks
> > > > > available
> > > > */
> > > > > u32 rotation_memory[2];
> > > > > +
> > > > > + /* priority level of RQOS register used for driven the ARQOS signal
> > */
> > > > > + u32 arqos_value;
> > > > > };
> > > > >
> > > > > static inline u32 malidp_hw_read(struct malidp_hw_device *hwdev,
> > > > > u32
> > > > > reg) diff --git a/drivers/gpu/drm/arm/malidp_regs.h
> > > > > b/drivers/gpu/drm/arm/malidp_regs.h
> > > > > index 993031542fa1..514c50dcb74d 100644
> > > > > --- a/drivers/gpu/drm/arm/malidp_regs.h
> > > > > +++ b/drivers/gpu/drm/arm/malidp_regs.h
> > > > > @@ -210,6 +210,16 @@
> > > > > #define MALIDP500_CONFIG_VALID 0x00f00
> > > > > #define MALIDP500_CONFIG_ID 0x00fd4
> > > > >
> > > > > +/*
> > > > > + * The quality of service (QoS) register on the DP500. RQOS
> > > > > +register values
> > > > > + * are driven by the ARQOS signal, using AXI transacations,
> > > > > +dependent on the
> > > > > + * FIFO input level.
> > > > > + * The RQOS register can also set QoS levels for:
> > > > > + * - RED_ARQOS @ A 4-bit signal value for close to underflow
> > > > conditions
> > > > > + * - GREEN_ARQOS @ A 4-bit signal value for normal conditions
> > > > > + */
> > > > > +#define MALIDP500_RQOS_QUALITY 0x00500
> > > > > +
> > > > > /* register offsets and bits specific to DP550/DP650 */
> > > > > #define MALIDP550_ADDR_SPACE_SIZE 0x10000
> > > > > #define MALIDP550_DE_CONTROL 0x00010
> > > > > --
> > > > > 2.17.1
> > > > >
> > > >
> > > > --
> > > > ====================
> > > > | I would like to |
> > > > | fix the world, |
> > > > | but they're not |
> > > > | giving me the |
> > > > \ source code! /
> > > > ---------------
> > > > ¯\_(ツ)_/¯
> >
> > --
> > ====================
> > | I would like to |
> > | fix the world, |
> > | but they're not |
> > | giving me the |
> > \ source code! /
> > ---------------
> > ¯\_(ツ)_/¯
--
====================
| I would like to |
| fix the world, |
| but they're not |
| giving me the |
\ source code! /
---------------
¯\_(ツ)_/¯
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
