> -----Original Message-----
> From: Liviu Dudau <liviu.dudau@xxxxxxx>
> Sent: 2019年7月19日 19:46
> To: Wen He <wen.he_1@xxxxxxx>
> Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> brian.starkey@xxxxxxx; airlied@xxxxxxxx; daniel@xxxxxxxx; Leo Li
> <leoyang.li@xxxxxxx>
> Subject: [EXT] Re: [v2 1/3] drm/arm/mali-dp: Add display QoS interface
> configuration for Mali DP500
>
> Caution: EXT Email
>
> On Fri, Jul 19, 2019 at 05:54:45PM +0800, Wen He wrote:
> > Configure the display Quality of service (QoS) levels priority if the
> > optional property node "arm,malidp-aqros-value" is defined in DTS file.
> >
> > QoS signaling using AQROS and AWQOS AXI interface signals, the AQROS
> > is driven from the "RQOS" register, so needed to program the RQOS
> > register to avoid the 4k resolution flicker issue on the LS1028A platform.
> >
> > Signed-off-by: Wen He <wen.he_1@xxxxxxx>
> > ---
> > change in v2:
> > - modify some content based on feedback from maintainers
> >
> > drivers/gpu/drm/arm/malidp_drv.c | 6 ++++++
> > drivers/gpu/drm/arm/malidp_hw.c | 13 +++++++++++++
> > drivers/gpu/drm/arm/malidp_hw.h | 3 +++
> > drivers/gpu/drm/arm/malidp_regs.h | 10 ++++++++++
> > 4 files changed, 32 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/arm/malidp_drv.c
> > b/drivers/gpu/drm/arm/malidp_drv.c
> > index f25ec4382277..61c49a0668a7 100644
> > --- a/drivers/gpu/drm/arm/malidp_drv.c
> > +++ b/drivers/gpu/drm/arm/malidp_drv.c
> > @@ -818,6 +818,12 @@ static int malidp_bind(struct device *dev)
> >
> > malidp->core_id = version;
> >
> > + ret = of_property_read_u32(dev->of_node,
> > + "arm,malidp-arqos-value",
> > + &hwdev->arqos_value);
> > + if (ret)
> > + hwdev->arqos_value = 0x0;
>
> Is zero the default value that you want? I thought it was 0x00010001.
Actually, the register default value always is 0x00010001(can be found in RM document).
>
> > +
> > /* set the number of lines used for output of RGB data */
> > ret = of_property_read_u8_array(dev->of_node,
> > "arm,malidp-output-port-lines",
> > diff --git a/drivers/gpu/drm/arm/malidp_hw.c
> > b/drivers/gpu/drm/arm/malidp_hw.c index 50af399d7f6f..323683b1e9f7
> > 100644
> > --- a/drivers/gpu/drm/arm/malidp_hw.c
> > +++ b/drivers/gpu/drm/arm/malidp_hw.c
> > @@ -374,6 +374,19 @@ static void malidp500_modeset(struct
> malidp_hw_device *hwdev, struct videomode *
> > malidp_hw_setbits(hwdev, MALIDP_DISP_FUNC_ILACED,
> MALIDP_DE_DISPLAY_FUNC);
> > else
> > malidp_hw_clearbits(hwdev, MALIDP_DISP_FUNC_ILACED,
> > MALIDP_DE_DISPLAY_FUNC);
> > +
> > + /*
> > + * Program the RQoS register to avoid 4k resolution flicker
> > + * on the LS1028A.
> > + */
> > + if (hwdev->arqos_value) {
> > + val = hwdev->arqos_value;
> > +
> > + if (mode->pixelclock == 594000000)
>
> If I remember correctly, you declare the pixelclocks in the device tree, so I
> wonder if this is needed here. We should just set what value was in the DT
> regardless of the pixelclock, and then you manipulate the DT to choose one of
> your fixed resolutions and also set the QoS value.
Yes, you remember correctly, but
1. declare the pixelclocks in the device tree.
About this, I was hoping to discuss it with you. I want to implement another patch
that just declare 27MHz reference clock in the device tree and add a fake clock subsystem
to enable/display prepare to set PLL. I am thinking what to do next.
As I remember, I sent out a patch that "Disable checking for required pixel clock",
I think should be cancel it.
2. declare the fixed resolutions list in DTS.
Yes, Although I put four resolutions for supported list in DTS file, but this just a
workaround that If not enable EDID OR EDID is not available. Once EDID is enabled,
these resolutions list declare will be remove in DTS. so we can't use it as a condition
to set the QoS value.
Best Regards,
Wen
>
> Best regards,
> Liviu
>
> > + malidp_hw_setbits(hwdev, val,
> MALIDP500_RQOS_QUALITY);
> > + else
> > + malidp_hw_clearbits(hwdev, val,
> MALIDP500_RQOS_QUALITY);
> > + }
> > }
> >
> > int malidp_format_get_bpp(u32 fmt)
> > diff --git a/drivers/gpu/drm/arm/malidp_hw.h
> > b/drivers/gpu/drm/arm/malidp_hw.h index 968a65eed371..e4c36bc90bda
> > 100644
> > --- a/drivers/gpu/drm/arm/malidp_hw.h
> > +++ b/drivers/gpu/drm/arm/malidp_hw.h
> > @@ -251,6 +251,9 @@ struct malidp_hw_device {
> >
> > /* size of memory used for rotating layers, up to two banks available
> */
> > u32 rotation_memory[2];
> > +
> > + /* priority level of RQOS register used for driven the ARQOS signal */
> > + u32 arqos_value;
> > };
> >
> > static inline u32 malidp_hw_read(struct malidp_hw_device *hwdev, u32
> > reg) diff --git a/drivers/gpu/drm/arm/malidp_regs.h
> > b/drivers/gpu/drm/arm/malidp_regs.h
> > index 993031542fa1..514c50dcb74d 100644
> > --- a/drivers/gpu/drm/arm/malidp_regs.h
> > +++ b/drivers/gpu/drm/arm/malidp_regs.h
> > @@ -210,6 +210,16 @@
> > #define MALIDP500_CONFIG_VALID 0x00f00
> > #define MALIDP500_CONFIG_ID 0x00fd4
> >
> > +/*
> > + * The quality of service (QoS) register on the DP500. RQOS register
> > +values
> > + * are driven by the ARQOS signal, using AXI transacations, dependent
> > +on the
> > + * FIFO input level.
> > + * The RQOS register can also set QoS levels for:
> > + * - RED_ARQOS @ A 4-bit signal value for close to underflow
> conditions
> > + * - GREEN_ARQOS @ A 4-bit signal value for normal conditions
> > + */
> > +#define MALIDP500_RQOS_QUALITY 0x00500
> > +
> > /* register offsets and bits specific to DP550/DP650 */
> > #define MALIDP550_ADDR_SPACE_SIZE 0x10000
> > #define MALIDP550_DE_CONTROL 0x00010
> > --
> > 2.17.1
> >
>
> --
> ====================
> | I would like to |
> | fix the world, |
> | but they're not |
> | giving me the |
> \ source code! /
> ---------------
> ¯\_(ツ)_/¯
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
