Hi Angus,
Am Samstag, den 19.01.2019, 19:31 -0700 schrieb Angus Ainslie (Purism):
> On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted,
> since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
> to 500Mhz, so use 1:1 instead.
>
> based on NXP commit MLK-16841-1
>
> > Signed-off-by: Angus Ainslie (Purism) <angus@xxxxxxxx>
> ---
> .../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
> drivers/dma/imx-sdma.c | 20 +++++++++++++++----
> 2 files changed, 17 insertions(+), 4 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
> index 3c9a57a8443b..17544c1820b7 100644
> --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
> +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
> @@ -67,6 +67,7 @@ Optional properties:
> reg is the GPR register offset.
> shift is the bit position inside the GPR register.
> val is the value of the bit (0 or 1).
> +- fsl,ratio-1-1: AHB/SDMA core clock ration 1:1, 2:1 without this.
Why does this need a separate DT property? Shouldn't the driver be able
to infer this from the clock rates going into the SDMA hardware?
Regards,
Lucas
> Examples:
>
> diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
> index 0b3a67ff8e82..65dada21d3c1 100644
> --- a/drivers/dma/imx-sdma.c
> +++ b/drivers/dma/imx-sdma.c
> @@ -440,6 +440,8 @@ struct sdma_engine {
> > > unsigned int irq;
> > > dma_addr_t bd0_phys;
> > > struct sdma_buffer_descriptor *bd0;
> > + /* clock ratio for AHB:SDMA core. 1:1 is 1, 2:1 is 0*/
> > > + bool clk_ratio;
> };
>
> static int sdma_config_write(struct dma_chan *chan,
> @@ -662,8 +664,14 @@ static int sdma_run_channel0(struct sdma_engine *sdma)
> > dev_err(sdma->dev, "Timeout waiting for CH0 ready\n");
>
> > /* Set bits of CONFIG register with dynamic context switching */
> > - if (readl(sdma->regs + SDMA_H_CONFIG) == 0)
> > - writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG);
> > + if (readl(sdma->regs + SDMA_H_CONFIG) == 0) {
> > + if (sdma->clk_ratio)
> > + reg = SDMA_H_CONFIG_CSM | SDMA_H_CONFIG_ACR;
> > + else
> > + reg = SDMA_H_CONFIG_CSM;
> +
> > + writel_relaxed(reg, sdma->regs + SDMA_H_CONFIG);
> > + }
>
> > return ret;
> }
> @@ -1880,8 +1888,10 @@ static int sdma_init(struct sdma_engine *sdma)
> > writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR);
>
> > /* Set bits of CONFIG register but with static context switching */
> > - /* FIXME: Check whether to set ACR bit depending on clock ratios */
> > - writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);
> > + if (sdma->clk_ratio)
> > + writel_relaxed(SDMA_H_CONFIG_ACR, sdma->regs + SDMA_H_CONFIG);
> > + else
> > + writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);
>
> > writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR);
>
> @@ -1975,6 +1985,8 @@ static int sdma_probe(struct platform_device *pdev)
> > if (!sdma)
> > return -ENOMEM;
>
> > + sdma->clk_ratio = of_property_read_bool(np, "fsl,ratio-1-1");
> +
> > spin_lock_init(&sdma->channel_0_lock);
>
> > sdma->dev = &pdev->dev;
