On Thu, Sep 10, 2015 at 09:15:09AM +0900, Krzysztof Kozlowski wrote: > On 10.09.2015 05:15, Andreas Dannenberg wrote: > > On Wed, Sep 09, 2015 at 01:58:09PM +0900, Krzysztof Kozlowski wrote: > >> > >> So we have different bindings. Existing ones: > >> bq2415x.txt - ti,charge-current - maximum charging current in mA > >> bq24257.txt - ti,charge-current - maximum charging current in uA > >> bq25890.txt - ti,charge-current - maximum charging current in uA > >> bq24735.txt - ti,charge-current - charge current (?) in mA > > > > I just spent some time with the bq24735 datasheet and the way that > > device appears to work is putting the user in control of the charging > > process rather than implementing a fully automatic control loop, but > > either way I still think it's valid to call the property > > ti,charge-current and use a description of "maximum charging current" > > for that device (there is no DT bindings doc however). And yes the unit > > is mA as one can see from reverse-engineering the register settings. > > Just for the record: the units used by device registers are not related > to units used in DT binding. You can use whatever you want. The driver > should just convert them. > > > > > On a related note the datasheet for that device says you have to > > periodically re-send the charge current setting every 44...175s to keep > > charging with the configured current or disable the device's watchdog > > timer. Neither of which the driver seems to do. I can probably go back > > and get some HW and test if that driver actually works as advertised. > > (also see http://www.ti.com/lit/ds/symlink/bq24735.pdf, Page 21) > > I mentioned existing bindings for reference. To show that it's a mess. > However you cannot change them now (at least easily). You could add new > bindings and mark old as deprecated (still they would have to be > supported by the driver)... Understood. > >> bq2415x.txt - ti,current-limit - maximum current to be drawn in mA > >> > >> New bindings: > >> ti,charge-current (bq24261) - default charge current in mA > >> ti,max-charge-current (bq24261) - maximum charging current in mA > > > > This ti,max-charge-current is actually an interesting one. It's not a > > device setting as it does not impact any of the device registers at all. > > Instead, it's an artificial limit that can be set through DT that > > prevents somebody from going into sysfs and configuring a charge current > > higher than ti,max-charge-current. In other drivers I have seen that the > > sysfs property reflecting that max charge current is just read-only and > > gives you the maximum the HW is capable of. From a device point of view > > there is nothing configurable about this property. > > Hmmm, so now I wonder whether this should be a DT binding. The purpose > of DT isn't the control of the driver like enable some stuff, set some > value used by the driver. The DT provides information about hardware so > the driver could properly configure the device and work with it. > > Reason to put this into DT would be: > For example one device configuration (device, board, connected battery) > could handle one maximum value and the other configuration would require > lower one. The device and its capabilities (bq24257 for example) are the > same but configuration changes. Yes this could be useful in this case but this property only makes sense if userspace is allowed to change the actual charge current through sysfs as some drivers do including Ram's proposed bq24261 driver. But if we get rid of the general sysfs configurability of the charge current (which I say we should) we don't need that ti,max-charge-current property. Also see... http://marc.info/?l=linux-pm&m=143080413218161&w=2 > If all configurations of bq24261 device have the same maximum value then > it should not be a DT property but it should be hard-coded in the driver > instead. > > Ramakrishna, > Could you describe the reason behind "ti,max-charge-current" and > "pdata.max_cc" in bq24261 driver? [...] > >> There is no way to unify or make consistent all of these bindings. > >> However one could try to add new stuff in a more sensible way. For > >> example how about (for bq2425x-charger and bq24261_charger... BTW notice > >> even the difference in using underscore and hyphen!): > > > > :( You are talking about the driver .name, right? I saw that too. If > > the bq24261 charger was to change it's device name to use a hyphen at > > least it would be consistent with bq2415x and bq2425x. > > The name of file and name of driver. Most of existing bq* drivers have > "_" in file name and "-" in driver name. So maybe use it in > bq2425x-charger (file name: bq2425x_charger)? Yes the bq2425x_charger already follows the same trend - underscore in the filename and dash in the driver name. The bq26261_charger.c driver is the one that should be adopted (already provided feedback on a separate thread). > To prevent future issues in naming and bindings consistency maybe there > should be a dedicated maintainer for bq/TI charger devices? Pali Rohar > recently took care for devices related to Nokia N900 but maybe someone > from TI should also take care of rest or all of them (if TI is > interested in this)? I'd be happy to step in here. Let me know how I can help and contribute. [...] > >> ti,current-limit (bq2425x) - maximum current to be drawn in *uA* > > > > Ok. Again here my preference would be mA. Like already on the bq2415x. > > If we can change the bq2425x driver to mA (see separate thread) we'd be > > closer to a more unified set of properties. Otherwise we would have > > properties with the same name but different units (is this even > > possible?). > > mA would be nice... but bq2425x driver must support existing device > which means it must support existing bindings. Unfortunately the > existing binding for bq24257 is in uA. Ok understood. I guess I interpreted your previous statement with you being ok with either milli or micro too broadly. Will stick to what we have then. Regards, -- Andreas Dannenberg Texas Instruments Inc -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html