Hi,
On 08/27/2015 11:12 AM, Marek Vasut wrote:
> On Thursday, August 27, 2015 at 07:44:34 PM, vikas wrote:
>> Hi,
>>
>> On 08/21/2015 02:20 AM, Marek Vasut wrote:
>>> From: Graham Moore <grmoore@xxxxxxxxxxxxxxxxxxxxx>
>>>
>>> Add binding document for the Cadence QSPI controller.
>>>
>>> Signed-off-by: Graham Moore <grmoore@xxxxxxxxxxxxxxxxxxxxx>
>>> Signed-off-by: Marek Vasut <marex@xxxxxxx>
>>> Cc: Alan Tull <atull@xxxxxxxxxxxxxxxxxxxxx>
>>> Cc: Brian Norris <computersforpeace@xxxxxxxxx>
>>> Cc: David Woodhouse <dwmw2@xxxxxxxxxxxxx>
>>> Cc: Dinh Nguyen <dinguyen@xxxxxxxxxxxxxxxxxxxxx>
>>> Cc: Graham Moore <grmoore@xxxxxxxxxxxxxxxxxxxxx>
>>> Cc: Vikas MANOCHA <vikas.manocha@xxxxxx>
>>> Cc: Yves Vandervennet <yvanderv@xxxxxxxxxxxxxxxxxxxxx>
>>> Cc: devicetree@xxxxxxxxxxxxxxx
>>> ---
>>>
>>> .../devicetree/bindings/mtd/cadence-quadspi.txt | 56
>>> ++++++++++++++++++++++ 1 file changed, 56 insertions(+)
>>> create mode 100644
>>> Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>>>
>>> V2: Add cdns prefix to driver-specific bindings.
>>> V3: Use existing property "is-decoded-cs" instead of creating a
>>>
>>> duplicate, "ext-decoder". Timing parameters are in nanoseconds,
>>> not master reference clocks. Remove bus-num completely.
>>>
>>> V4: Add new properties fifo-width and trigger-address
>>> V7: - Prefix all of the Cadence-specific properties with cdns prefix,
>>>
>>> those are in particular "cdns,is-decoded-cs", "cdns,fifo-depth",
>>> "cdns,fifo-width", "cdns,trigger-address".
>>>
>>> - Drop bogus properties which were not used and were incorrect.
>>>
>>> V8: Align lines to 80 chars.
>>>
>>> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>>> b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt new file
>>> mode 100644
>>> index 0000000..f248056
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>>> @@ -0,0 +1,56 @@
>>> +* Cadence Quad SPI controller
>>> +
>>> +Required properties:
>>> +- compatible : Should be "cdns,qspi-nor".
>>> +- reg : Contains two entries, each of which is a tuple consisting of a
>>> + physical address and length. The first entry is the address and
>>> + length of the controller register set. The second entry is the
>>> + address and length of the QSPI Controller data area.
>>
>> still hooked up with "Controller data area", it is ambiguous.
>> Use something which is more clear: Nor Flash memory mapped address.
>
> I have to disagree, I will call it whatever it is called in the datasheet
> and it is called "controller data area".
It is preferable to use terminology which readers understand & that is the purpose
of explaining it here otherwise we could have just pasted the doc link.
I have to stop here for this point.
>
>>> +- interrupts : Unit interrupt specifier for the controller interrupt.
>>> +- clocks : phandle to the Quad SPI clock.
>>> +- cdns,fifo-depth : Size of the data FIFO in words.
>>> +- cdns,fifo-width : Bus width of the data FIFO in bytes.
>>> +- cdns,trigger-address : 32-bit indirect AHB trigger address.
>>> +
>>
>>> +Optional properties:
>> again, is it optional ? can the driver be used without these properties ?
>
> Why wouldn't it be possible to use the driver with no SPI NOR attached to
> it? It's a cornercase, but still a valid one.
that's not right, this controller is only spi flash controller.
>
>>> +- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>>
>> again, add info what the decoder is for ?
>
> This is something Graham has to clarify. Based on the code (I'm sure you did
> check the code), it's a 4:16 demuxer.
Please clarify if possible & add the info for others benefit. This part is not common in other spi/nor controllers.
>
>>> +
>>> +Optional subnodes:
>>> +Subnodes of the Cadence Quad SPI controller are spi slave nodes with
>>> additional +custom properties:
>>> +- cdns,read-delay : Delay for read capture logic, in clock cycles
>>> +- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>>> + mode chip select outputs are de-asserted between
>>> + transactions.
>>> +- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>>> + de-activated and the activation of another.
>>> +- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>>> + transaction and deasserting the device chip select
>>> + (qspi_n_ss_out).
>>> +- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>>> + and first bit transfer.
>>> +
>>> +Example:
>>> +
>>> + qspi: spi@ff705000 {
>>> + compatible = "cdns,qspi-nor";
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <0xff705000 0x1000>,
>>> + <0xffa00000 0x1000>;
>>> + interrupts = <0 151 4>;
>>> + clocks = <&qspi_clk>;
>>> + cdns,is-decoded-cs;
>>
>> flag value ?
>
> Sorry, I don't quite understand the question. If you mean why there is no
> value, it's because this is a boolean OF node, which just does't need to
> have a value ; it's either present or not.
you are right, thanks.
Cheers,
Vikas
>
> Best regards,
> Marek Vasut
> .
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
