On 27 May 2015 at 16:49, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote: > On 05/27/2015 08:18 AM, Tomeu Vizoso wrote: >> >> On 26 May 2015 at 21:41, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote: >>> >>> On 05/25/2015 08:53 AM, Tomeu Vizoso wrote: >>>> >>>> >>>> Specify how the GPIOs map to the pins in T124, so the dependency is >>>> explicit. >>>> >>>> Signed-off-by: Tomeu Vizoso <tomeu.vizoso@xxxxxxxxxxxxx> >>>> --- >>>> arch/arm/boot/dts/tegra124.dtsi | 1 + >>>> 1 file changed, 1 insertion(+) >>>> >>>> diff --git a/arch/arm/boot/dts/tegra124.dtsi >>>> b/arch/arm/boot/dts/tegra124.dtsi >>>> index 13cc7ca..5d1d35f 100644 >>>> --- a/arch/arm/boot/dts/tegra124.dtsi >>>> +++ b/arch/arm/boot/dts/tegra124.dtsi >>>> @@ -254,6 +254,7 @@ >>>> gpio-controller; >>>> #interrupt-cells = <2>; >>>> interrupt-controller; >>>> + gpio-ranges = <&pinmux 0 0 250>; >>> >>> >>> >>> We should be consistent between SoCs. Why not make the same change for >>> all >>> Tegra SoCs? >>> >>> I think this change will cause the GPIO subsystem to call into the >>> pinctrl >>> subsystem and create/add/register a new GPIO<->pinctrl range structure. >>> The >>> pinctrl driver already does this, so I think we'll end up with two >>> duplicate >>> entries in the pinctrl device's gpio_ranges list. This probably won't >>> cause >>> a problem, but I wanted to make sure you'd thought about it to make sure. >> >> >> Actually, I have checked and see that gpio-tegra.c registers 256 >> gpios, but pinctrl-tegra124.c adds a range of only 251. I don't really >> remember where I got the 250 value from, sorry :( >> >> I don't see how that would cause any concrete problems, but maybe we >> should have a single authoritative source (not sure we can do so >> without breaking DT ABI though). >> >>> Right now, I think we get lucky and pinctrl ends up probing first (or at >>> least very early) anyway. Somewhat related to this series, I wonder if we >>> shouldn't add pinctrl client properties to every node in the Tegra DT >>> that >>> describes a controller that makes use of external pins that are affected >>> by >>> the pinmux. Such a change would guarantee this desired probing order. In >>> order to preserve the "program the entire pinmux at once" semantics, >>> these >>> new pinctrl client properties would all need to reference empty states, >>> yet >>> would still need to exist to represent the dependency. >> >> >> I think so, but aren't almost all those pins used as gpios? If so, >> then such a controller's driver will request the gpio it wants which >> will cause the gpio driver to be registered (and hopefully probed) if >> needed, which in turn will check that the corresponding pinctrl device >> has been registered. Or am I missing something? > > > As you say this probably works out fine for pins that are used as GPIOs. I > was thinking more about SFIOs. Take an I2C controller, which doesn't use any > GPIOs itself. The pinctrl device should be probed before the I2C device, so > that the I2C driver can initiate transactions on the I2C bus during its > probe if it wanted to (or at least, clients could initiate transactions at > any completely arbitrary time as soon as probe was complete). What is using the SFIO in this case, the I2C master or the I2C client? In any case, is the problem you are referring to that ICs may rely on a specific pinmux configuration but that's not currently reflected on the DT because pinmux configuration happened so early that things just worked? Thanks, Tomeu -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html