On 05/28/2015 02:26 AM, Tomeu Vizoso wrote:
On 27 May 2015 at 16:49, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote:
On 05/27/2015 08:18 AM, Tomeu Vizoso wrote:
On 26 May 2015 at 21:41, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote:
On 05/25/2015 08:53 AM, Tomeu Vizoso wrote:
Specify how the GPIOs map to the pins in T124, so the dependency is
explicit.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@xxxxxxxxxxxxx>
---
arch/arm/boot/dts/tegra124.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/tegra124.dtsi
b/arch/arm/boot/dts/tegra124.dtsi
index 13cc7ca..5d1d35f 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/tegra124.dtsi
@@ -254,6 +254,7 @@
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
+ gpio-ranges = <&pinmux 0 0 250>;
We should be consistent between SoCs. Why not make the same change for
all
Tegra SoCs?
I think this change will cause the GPIO subsystem to call into the
pinctrl
subsystem and create/add/register a new GPIO<->pinctrl range structure.
The
pinctrl driver already does this, so I think we'll end up with two
duplicate
entries in the pinctrl device's gpio_ranges list. This probably won't
cause
a problem, but I wanted to make sure you'd thought about it to make sure.
Actually, I have checked and see that gpio-tegra.c registers 256
gpios, but pinctrl-tegra124.c adds a range of only 251. I don't really
remember where I got the 250 value from, sorry :(
I don't see how that would cause any concrete problems, but maybe we
should have a single authoritative source (not sure we can do so
without breaking DT ABI though).
Right now, I think we get lucky and pinctrl ends up probing first (or at
least very early) anyway. Somewhat related to this series, I wonder if we
shouldn't add pinctrl client properties to every node in the Tegra DT
that
describes a controller that makes use of external pins that are affected
by
the pinmux. Such a change would guarantee this desired probing order. In
order to preserve the "program the entire pinmux at once" semantics,
these
new pinctrl client properties would all need to reference empty states,
yet
would still need to exist to represent the dependency.
I think so, but aren't almost all those pins used as gpios? If so,
then such a controller's driver will request the gpio it wants which
will cause the gpio driver to be registered (and hopefully probed) if
needed, which in turn will check that the corresponding pinctrl device
has been registered. Or am I missing something?
As you say this probably works out fine for pins that are used as GPIOs. I
was thinking more about SFIOs. Take an I2C controller, which doesn't use any
GPIOs itself. The pinctrl device should be probed before the I2C device, so
that the I2C driver can initiate transactions on the I2C bus during its
probe if it wanted to (or at least, clients could initiate transactions at
any completely arbitrary time as soon as probe was complete).
What is using the SFIO in this case, the I2C master or the I2C client?
The I2C controller a/k/a the I2C master.
In any case, is the problem you are referring to that ICs may rely on
s/ICs/drivers/ I think.
a specific pinmux configuration but that's not currently reflected on
the DT because pinmux configuration happened so early that things just
worked?
Yes; the dependency of some nodes on pinctrl isn't explicitly called out
in the DT. It's probably not a good idea to have such implicit
dependencies, although I suppose for something so central as pinmux,
maybe it's not terrible, since almost everything depends on it and it's
pretty obvious.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
