On 12/11/2024 3:12 AM, Rob Herring (Arm) wrote:
On Mon, 09 Dec 2024 16:04:51 +0530, Janaki Ramaiah Thota wrote:
- Patch 1/4 Add description of the PMU of the WCN6750 module.
- Patch 2/4 add and enable BT node for qcs6490-rb3gen board.
- Patch 3/4 use the power sequencer for wcn6750.
- Patch 4/4 add support for the WCN6750 PMU.
----
Changes from v4:
* Added reviewed tag by Krzysztof in p1
* Updated the p2 commit message with sw_ctrl and wifi-enable are
handled in wifi FW.
* Added blank line between the nodes in p2
* Placed the structures in proper order in p4
* Link to v4: https://lore.kernel.org/all/20241204131706.20791-1-quic_janathot@xxxxxxxxxxx/
Changes from v3:
* Defined the PMU node and used the its output to power up BT
* Used power sequencer for wcn wcn6750 module
* Split the patch to multiple as per subtree
* Add description of the PMU of the WCN6750 module
* Include separate UART state node for sleep pin configuarion
* Link to v3: https://lore.kernel.org/linux-arm-msm/20241022104600.3228-1-quic_janathot@xxxxxxxxxxx/
Changes from v2:
* Sorted nodes alphabetically
* Link to v2: https://lore.kernel.org/linux-arm-msm/20241010105107.30118-1-quic_janathot@xxxxxxxxxxx/
Changes from v1:
* Corrected the board name in subject
* Link to v1: https://lore.kernel.org/linux-arm-msm/20241009111436.23473-1-quic_janathot@xxxxxxxxxxx/
Janaki Ramaiah Thota (4):
regulator:·dt-bindings:·qcom,qca6390-pmu:·document wcn6750-pmu
arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node
Bluetooth: hci_qca: use the power sequencer for wcn6750
power: sequencing: qcom-wcn: add support for the WCN6750 PMU
.../bindings/regulator/qcom,qca6390-pmu.yaml | 27 +++
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 168 +++++++++++++++++-
drivers/bluetooth/hci_qca.c | 2 +-
drivers/power/sequencing/pwrseq-qcom-wcn.c | 22 +++
4 files changed, 217 insertions(+), 2 deletions(-)
--
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y qcom/qcs6490-rb3gen2.dtb' for 20241209103455.9675-1-quic_janathot@xxxxxxxxxxx:
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'enable-gpios' is a required property
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'swctrl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddio-supply' is a required property
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddbtcxmx-supply' is a required property
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddasd-supply' is a required property
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: pinctrl@f100000: Unevaluated properties are not allowed ('qup_uart7_sleep' was unexpected)
from schema $id: http://devicetree.org/schemas/pinctrl/qcom,sc7280-pinctrl.yaml#
Since the DTS files for all boards using the WCN6750 BT chip are not
updated according to the PMU node, updating the
bluetooth/qualcomm-bluetooth.yaml file will result in similar warnings
for other boards.
Thanks,
Janakiram
