On Mon, 09 Dec 2024 16:04:51 +0530, Janaki Ramaiah Thota wrote: > - Patch 1/4 Add description of the PMU of the WCN6750 module. > - Patch 2/4 add and enable BT node for qcs6490-rb3gen board. > - Patch 3/4 use the power sequencer for wcn6750. > - Patch 4/4 add support for the WCN6750 PMU. > > ---- > Changes from v4: > * Added reviewed tag by Krzysztof in p1 > * Updated the p2 commit message with sw_ctrl and wifi-enable are > handled in wifi FW. > * Added blank line between the nodes in p2 > * Placed the structures in proper order in p4 > * Link to v4: https://lore.kernel.org/all/20241204131706.20791-1-quic_janathot@xxxxxxxxxxx/ > > Changes from v3: > * Defined the PMU node and used the its output to power up BT > * Used power sequencer for wcn wcn6750 module > * Split the patch to multiple as per subtree > * Add description of the PMU of the WCN6750 module > * Include separate UART state node for sleep pin configuarion > * Link to v3: https://lore.kernel.org/linux-arm-msm/20241022104600.3228-1-quic_janathot@xxxxxxxxxxx/ > > Changes from v2: > * Sorted nodes alphabetically > * Link to v2: https://lore.kernel.org/linux-arm-msm/20241010105107.30118-1-quic_janathot@xxxxxxxxxxx/ > > Changes from v1: > * Corrected the board name in subject > * Link to v1: https://lore.kernel.org/linux-arm-msm/20241009111436.23473-1-quic_janathot@xxxxxxxxxxx/ > > Janaki Ramaiah Thota (4): > regulator:·dt-bindings:·qcom,qca6390-pmu:·document wcn6750-pmu > arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node > Bluetooth: hci_qca: use the power sequencer for wcn6750 > power: sequencing: qcom-wcn: add support for the WCN6750 PMU > > .../bindings/regulator/qcom,qca6390-pmu.yaml | 27 +++ > arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 168 +++++++++++++++++- > drivers/bluetooth/hci_qca.c | 2 +- > drivers/power/sequencing/pwrseq-qcom-wcn.c | 22 +++ > 4 files changed, 217 insertions(+), 2 deletions(-) > > -- > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y qcom/qcs6490-rb3gen2.dtb' for 20241209103455.9675-1-quic_janathot@xxxxxxxxxxx: arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'enable-gpios' is a required property from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'swctrl-gpios' is a required property from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddio-supply' is a required property from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddbtcxmx-supply' is a required property from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddasd-supply' is a required property from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml# arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: pinctrl@f100000: Unevaluated properties are not allowed ('qup_uart7_sleep' was unexpected) from schema $id: http://devicetree.org/schemas/pinctrl/qcom,sc7280-pinctrl.yaml#
