On Fri, Oct 25, 2024 at 03:52:58PM +0200, Geert Uytterhoeven wrote:
> Hi Frank,
>
> On Wed, Oct 23, 2024 at 11:07 PM Frank Li <Frank.Li@xxxxxxx> wrote:
> > Fix the issue where both 'output-low' and 'output-high' exist under GPIO
> > hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
> > tree overlays. Since /delete-property/ is not supported in the overlays,
> > setting 'output-low' results in both properties being present. The
> > workaround is to disable these hogs and create new ones with 'output-low'
> > as needed.
> >
> > Fix below CHECK_DTBS warning:
> > arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
> > {'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
> > is valid under each of {'required': ['output-low']}, {'required': ['output-high']
> >
> > Fixes: 3f6fc30abebc ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
> > Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
> > ---
> > Alex:
> > I have not hardware to run it. I check dtb output is correct.
> > ---
> > .../imx8mn-tqma8mqnl-mba8mx-usbotg.dtso | 29 +++++++++++++++++--
> > 1 file changed, 27 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> > index 96db07fc9bece..1f2a0fe70a0a2 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> > +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> > @@ -29,12 +29,37 @@ usb_dr_connector: endpoint {
> > };
> > };
> >
> > +/*
> > + * rst_usb_hub_hog and sel_usb_hub_hog have property 'output-high',
> > + * dt overlay don't support /delete-property/. Both 'output-low' and
> > + * 'output-high' will be exist under hog nodes if overlay file set
> > + * 'output-low'. Workaround is disable these hog and create new hog with
> > + * 'output-low'.
> > + */
> > +
> > &rst_usb_hub_hog {
> > - output-low;
> > + status = "disabled";
> > +};
> > +
> > +&expander0 {
> > + rst-usb-low-hub-hog {
> > + gpio-hog;
> > + gpios = <13 0>;
> > + output-low;
> > + line-name = "RST_USB_HUB#";
> > + };
> > };
> >
> > &sel_usb_hub_hog {
> > - output-low;
> > + status = "disabled";
> > +};
> > +
> > +&gpio2 {
> > + sel-usb-low-hub-hog {
> > + gpio-hog;
> > + gpios = <1 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + };
> > };
> >
> > &usbotg1 {
>
> Note that after this, there is still
>
> /delete-property/ disable-over-current;
>
> left, which does not actually remove the property.
>
> Gr{oetje,eeting}s,
Yes, but it should not impact much. I hope Alex or other tq-group's
engineer can fix it. I have not hardware to test it.
Frank
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
