On Fri, Aug 09, 2024 at 03:43:22AM +0200, Konrad Dybcio wrote:
> From: Konrad Dybcio <quic_kdybcio@xxxxxxxxxxx>
>
> GENI SE2 within QUP0 is used as UART on some devices, describe it.
>
> Signed-off-by: Konrad Dybcio <quic_kdybcio@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/x1e80100.dtsi | 52 ++++++++++++++++++++++++++++++++++
> 1 file changed, 52 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index 326283822aee..a2a011702752 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -2142,6 +2142,28 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
> status = "disabled";
> };
>
> + uart2: serial@b88000 {
> + compatible = "qcom,geni-uart";
> + reg = <0 0x00b88000 0 0x4000>;
> +
> + interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + clock-names = "se";
> +
> + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
> + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> + &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "qup-core",
> + "qup-config";
> +
> + pinctrl-0 = <&qup_uart2_default>;
> + pinctrl-names = "default";
> +
> + status = "disabled";
> + };
> +
> spi2: spi@b88000 {
> compatible = "qcom,geni-spi";
> reg = <0 0x00b88000 0 0x4000>;
> @@ -5365,6 +5387,36 @@ qup_spi23_data_clk: qup-spi23-data-clk-state {
> bias-disable;
> };
>
> + qup_uart2_default: qup-uart2-default-state {
> + cts-pins {
> + pins = "gpio8";
> + function = "qup0_se2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rts-pins {
> + pins = "gpio9";
> + function = "qup0_se2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + tx-pins {
> + pins = "gpio10";
> + function = "qup0_se2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx-pins {
> + pins = "gpio11";
> + function = "qup0_se2";
> + drive-strength = <2>;
> + bias-disable;
> + };
Can you combine these into a single entry, i.e.
pins = "gpio8", "gpio9", "gpio10", "gpio11";
if they are all the same?
Thanks,
Stephan
