Add QPS615 PCIe switch node which has 3 downstream ports and in one
downstream port two embedded ethernet devices are present.
Power to the QPS615 is supplied through two LDO regulators, controlled
by two GPIOs, these are added as fixed regulators.
Add i2c device node which is used to configure the switch.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 121 +++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280.dtsi | 2 +-
2 files changed, 122 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 0d45662b8028..59d209768636 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -202,6 +202,30 @@ vph_pwr: vph-pwr-regulator {
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
};
+
+ vdd_ntn_0p9: regulator-vdd-ntn-0p9 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_NTN_0P9";
+ gpio = <&pm8350c_gpios 2 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <899400>;
+ regulator-max-microvolt = <899400>;
+ enable-active-high;
+ pinctrl-0 = <&ntn_0p9_en>;
+ pinctrl-names = "default";
+ regulator-enable-ramp-delay = <4300>;
+ };
+
+ vdd_ntn_1p8: regulator-vdd-ntn-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_NTN_1P8";
+ gpio = <&pm8350c_gpios 3 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ pinctrl-0 = <&ntn_1p8_en>;
+ pinctrl-names = "default";
+ regulator-enable-ramp-delay = <10000>;
+ };
};
&apps_rsc {
@@ -595,6 +619,12 @@ lt9611_out: endpoint {
};
};
};
+
+ qps615_switch: pcie-switch@77 {
+ compatible = "qcom,qps615";
+ reg = <0x77>;
+ status = "okay";
+ };
};
&i2c1 {
@@ -688,6 +718,75 @@ &pmk8350_rtc {
status = "okay";
};
+&pcie1 {
+ status = "okay";
+};
+
+&pcieport {
+ pcie@0,0 {
+ compatible = "pci1179,0623";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+
+ vddc-supply = <&vdd_ntn_0p9>;
+ vdd18-supply = <&vdd_ntn_1p8>;
+ vdd09-supply = <&vdd_ntn_0p9>;
+ vddio1-supply = <&vdd_ntn_1p8>;
+ vddio2-supply = <&vdd_ntn_1p8>;
+ vddio18-supply = <&vdd_ntn_1p8>;
+
+ qcom,qps615-controller = <&qps615_switch>;
+
+ reset-gpios = <&pm8350c_gpios 1 GPIO_ACTIVE_LOW>;
+
+ pcie@1,0 {
+ reg = <0x20800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ };
+
+ pcie@2,0 {
+ reg = <0x21000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ };
+
+ pcie@3,0 {
+ reg = <0x21800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+
+ pcie@0,0 {
+ reg = <0x50000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+
+ pcie@0,1 {
+ reg = <0x50100 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+ };
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -812,6 +911,28 @@ lt9611_rst_pin: lt9611-rst-state {
};
};
+&pm8350c_gpios {
+ ntn_0p9_en: ntn-0p9-en-state {
+ pins = "gpio2";
+ function = "normal";
+
+ bias-disable;
+ input-disable;
+ output-enable;
+ power-source = <0>;
+ };
+
+ ntn_1p8_en: ntn-1p8-en-state {
+ pins = "gpio3";
+ function = "normal";
+
+ bias-disable;
+ input-disable;
+ output-enable;
+ power-source = <0>;
+ };
+};
+
&tlmm {
lt9611_irq_pin: lt9611-irq-state {
pins = "gpio24";
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 3d8410683402..3840f056b7f2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2279,7 +2279,7 @@ pcie1: pcie@1c08000 {
status = "disabled";
- pcie@0 {
+ pcieport: pcie@0 {
device_type = "pci";
reg = <0x0 0x0 0x0 0x0 0x0>;
bus-range = <0x01 0xff>;
--
2.34.1
