Hi Krishna,
On 03/08/2024 05:22, Krishna chaitanya chundru wrote:
> Add QPS615 PCIe switch node which has 3 downstream ports and in one
> downstream port two embedded ethernet devices are present.
>
> Power to the QPS615 is supplied through two LDO regulators, controlled
> by two GPIOs, these are added as fixed regulators.
>
> Add i2c device node which is used to configure the switch.
>
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 121 +++++++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/sc7280.dtsi | 2 +-
> 2 files changed, 122 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> index 0d45662b8028..59d209768636 100644
> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> @@ -202,6 +202,30 @@ vph_pwr: vph-pwr-regulator {
> regulator-min-microvolt = <3700000>;
> regulator-max-microvolt = <3700000>;
> };
> +
> + vdd_ntn_0p9: regulator-vdd-ntn-0p9 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_NTN_0P9";
> + gpio = <&pm8350c_gpios 2 GPIO_ACTIVE_HIGH>;
> + regulator-min-microvolt = <899400>;
> + regulator-max-microvolt = <899400>;
> + enable-active-high;
> + pinctrl-0 = <&ntn_0p9_en>;
> + pinctrl-names = "default";
> + regulator-enable-ramp-delay = <4300>;
> + };
> +
> + vdd_ntn_1p8: regulator-vdd-ntn-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_NTN_1P8";
> + gpio = <&pm8350c_gpios 3 GPIO_ACTIVE_HIGH>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + enable-active-high;
> + pinctrl-0 = <&ntn_1p8_en>;
> + pinctrl-names = "default";
> + regulator-enable-ramp-delay = <10000>;
> + };
> };
>
> &apps_rsc {
> @@ -595,6 +619,12 @@ lt9611_out: endpoint {
> };
> };
> };
> +
> + qps615_switch: pcie-switch@77 {
> + compatible = "qcom,qps615";
> + reg = <0x77>;
> + status = "okay";
> + };
> };
>
> &i2c1 {
> @@ -688,6 +718,75 @@ &pmk8350_rtc {
> status = "okay";
> };
>
> +&pcie1 {
> + status = "okay";
> +};
Isn't it also necessary to configure the phy as well? It's also default
disabled and has two regulators.
Kind regards,
> +
> +&pcieport {
> + pcie@0,0 {
> + compatible = "pci1179,0623";
> + reg = <0x10000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + device_type = "pci";
> + ranges;
> +
> + vddc-supply = <&vdd_ntn_0p9>;
> + vdd18-supply = <&vdd_ntn_1p8>;
> + vdd09-supply = <&vdd_ntn_0p9>;
> + vddio1-supply = <&vdd_ntn_1p8>;
> + vddio2-supply = <&vdd_ntn_1p8>;
> + vddio18-supply = <&vdd_ntn_1p8>;
> +
> + qcom,qps615-controller = <&qps615_switch>;
> +
> + reset-gpios = <&pm8350c_gpios 1 GPIO_ACTIVE_LOW>;
> +
> + pcie@1,0 {
> + reg = <0x20800 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + device_type = "pci";
> + ranges;
> + };
> +
> + pcie@2,0 {
> + reg = <0x21000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + device_type = "pci";
> + ranges;
> + };
> +
> + pcie@3,0 {
> + reg = <0x21800 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> +
> + pcie@0,0 {
> + reg = <0x50000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + };
> +
> + pcie@0,1 {
> + reg = <0x50100 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + };
> + };
> + };
> +};
> +
> &qupv3_id_0 {
> status = "okay";
> };
> @@ -812,6 +911,28 @@ lt9611_rst_pin: lt9611-rst-state {
> };
> };
>
> +&pm8350c_gpios {
> + ntn_0p9_en: ntn-0p9-en-state {
> + pins = "gpio2";
> + function = "normal";
> +
> + bias-disable;
> + input-disable;
> + output-enable;
> + power-source = <0>;
> + };
> +
> + ntn_1p8_en: ntn-1p8-en-state {
> + pins = "gpio3";
> + function = "normal";
> +
> + bias-disable;
> + input-disable;
> + output-enable;
> + power-source = <0>;
> + };
> +};
> +
> &tlmm {
> lt9611_irq_pin: lt9611-irq-state {
> pins = "gpio24";
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 3d8410683402..3840f056b7f2 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -2279,7 +2279,7 @@ pcie1: pcie@1c08000 {
>
> status = "disabled";
>
> - pcie@0 {
> + pcieport: pcie@0 {
> device_type = "pci";
> reg = <0x0 0x0 0x0 0x0 0x0>;
> bus-range = <0x01 0xff>;
>
--
// Caleb (they/them)
