Re: [PATCH v3 1/3] dt-bindings: iio: adc: add a7779 doc

[Conor Dooley <conor@xxxxxxxxxx>]

On Wed, Jun 19, 2024 at 03:20:44PM +0300, Ramona Alexandra Nechita wrote:
> Add dt bindings for adc ad7779.
> 
> Signed-off-by: Ramona Alexandra Nechita <ramona.nechita@xxxxxxxxxx>
> ---
>  .../bindings/iio/adc/adi,ad7779.yaml          | 84 +++++++++++++++++++
>  1 file changed, 84 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml
> new file mode 100644
> index 000000000000..f1eec656acec
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml
> @@ -0,0 +1,84 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/adi,ad7779.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices AD777X family 8-Channel, 24-Bit, Simultaneous Sampling ADCs
> +
> +maintainers:
> +  - Ramona Nechita <ramona.nechita@xxxxxxxxxx>
> +
> +description: |
> +  The AD777X family consist of 8-channel, simultaneous sampling analog-to-
> +  digital converter (ADC). Eight full Σ-Δ ADCs are on-chip. The
> +  AD7771 provides an ultralow input current to allow direct sensor
> +  connection. Each input channel has a programmable gain stage
> +  allowing gains of 1, 2, 4, and 8 to map lower amplitude sensor
> +  outputs into the full-scale ADC input range, maximizing the
> +  dynamic range of the signal chain.
> +
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7770.pdf
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7771.pdf
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7779.pdf
> +
> +$ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ad7770
> +      - adi,ad7771
> +      - adi,ad7779
> +
> +  reg:
> +    maxItems: 1
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0

Why does this device have address/size cells, but not have any child
nodes? Are you missing some channel child nodes? If you don't have
children, you don't need these properties.

Also, your patch is still not threaded with the other 2 patches in the
series (I see 1/3 in the subject). Where are those patches?

Thanks,
Conor.

> +
> +  clocks:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  vref-supply:
> +    description:
> +      ADC reference voltage supply
> +
> +  start-gpios:
> +    description:
> +      Pin that controls start synchronization pulse.
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +
> +unevaluatedProperties: false
> +
> +examples:
> +- |
> +  #include <dt-bindings/gpio/gpio.h>
> +  spi {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      adc@0 {
> +        compatible = "adi,ad7779";
> +        reg = <0>;
> +        vref-supply = <&vref>;
> +        start-gpios = <&gpio0 87 GPIO_ACTIVE_LOW>;
> +        reset-gpios = <&gpio0 93 GPIO_ACTIVE_LOW>;
> +        clocks = <&adc_clk>;
> +      };
> +  };
> +...
> -- 
> 2.43.0
>

Attachment: signature.asc
Description: PGP signature