[PATCH 3/9] dt-bindings: iio: adc: adi,ad7606: improve descriptions

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Reword a few descriptions, and normalize the text width to 80 characters.

Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx>
---
 .../devicetree/bindings/iio/adc/adi,ad7606.yaml    | 61 ++++++++++++----------
 1 file changed, 34 insertions(+), 27 deletions(-)

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index 00fdaed11cbd..80866940123c 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -36,64 +36,71 @@ properties:
   avcc-supply: true
 
   interrupts:
+    description:
+      The BUSY pin falling edge indicates that the conversion is over, and thus
+      new data is available.
     maxItems: 1
 
   adi,conversion-start-gpios:
     description:
-      Must be the device tree identifier of the CONVST pin.
-      This logic input is used to initiate conversions on the analog
-      input channels. As the line is active high, it should be marked
-      GPIO_ACTIVE_HIGH.
+      Must be the device tree identifier of the CONVST pin(s). This logic input
+      is used to initiate conversions on the analog input channels. As the line
+      is active high, it should be marked GPIO_ACTIVE_HIGH.
     maxItems: 1
 
   reset-gpios:
     description:
-      Must be the device tree identifier of the RESET pin. If specified,
-      it will be asserted during driver probe. As the line is active high,
-      it should be marked GPIO_ACTIVE_HIGH.
+      Must be the device tree identifier of the RESET pin. If specified, it will
+      be asserted during driver probe. On the AD7606x, as the line is active
+      high, it should be marked GPIO_ACTIVE_HIGH. On the AD7616, as the line is
+      active low, it should be marked GPIO_ACTIVE_LOW.
     maxItems: 1
 
   standby-gpios:
     description:
-      Must be the device tree identifier of the STBY pin. This pin is used
-      to place the AD7606 into one of two power-down modes, Standby mode or
+      Must be the device tree identifier of the STBY pin. This pin is used to
+      place the AD7606 into one of two power-down modes, Standby mode or
       Shutdown mode. As the line is active low, it should be marked
       GPIO_ACTIVE_LOW.
     maxItems: 1
 
   adi,first-data-gpios:
     description:
-      Must be the device tree identifier of the FRSTDATA pin.
-      The FRSTDATA output indicates when the first channel, V1, is
-      being read back on either the parallel, byte or serial interface.
-      As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
+      Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA
+      output indicates when the first channel, V1, is being read back on either
+      the parallel, byte or serial interface. As the line is active
+      high, it should be marked GPIO_ACTIVE_HIGH.
     maxItems: 1
 
   adi,range-gpios:
     description:
-      Must be the device tree identifier of the RANGE pin. The polarity on
-      this pin determines the input range of the analog input channels. If
-      this pin is tied to a logic high, the analog input range is ±10V for
-      all channels. If this pin is tied to a logic low, the analog input range
+      Must be the device tree identifier of the RANGE pin. The state on this
+      pin determines the input range of the analog input channels. If this pin
+      is tied to a logic high, the analog input range is ±10V for all channels.
+      On the AD760X, if this pin is tied to a logic low, the analog input range
       is ±5V for all channels. As the line is active high, it should be marked
-      GPIO_ACTIVE_HIGH.
+      GPIO_ACTIVE_HIGH. On the AD7616, there are 2 pins, and if the 2 pins are
+      tied to a logic high, software mode is enabled, otherwise one of the 3
+      possible range values is selected.
     maxItems: 1
 
   adi,oversampling-ratio-gpios:
     description:
-      Must be the device tree identifier of the over-sampling
-      mode pins. As the line is active high, it should be marked
-      GPIO_ACTIVE_HIGH.
+      Must be the device tree identifier of the over-sampling mode pins. As the
+      line is active high, it should be marked GPIO_ACTIVE_HIGH. On the AD7606X
+      parts that support it, if all 3 pins are tied to a logic high, software
+      mode is enabled.
     maxItems: 3
 
   adi,sw-mode:
     description:
-      Software mode of operation, so far available only for ad7616 and ad7606b.
-      It is enabled when all three oversampling mode pins are connected to
-      high level. The device is configured by the corresponding registers. If the
-      adi,oversampling-ratio-gpios property is defined, then the driver will set the
-      oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
-      to VDD.
+      Software mode of operation, so far available only for AD7616 and AD7606b.
+      It is enabled when all three oversampling mode pins are connected to high
+      level for the AD7606B, or all two range selection pins are connected to
+      high level for the AD7616. The device is configured by the corresponding
+      registers. If the adi,oversampling-ratio-gpios property is defined, then
+      the driver will set the oversampling gpios to high. Otherwise, it is
+      assumed that the pins are hardwired to VDD.
     type: boolean
 
 required:

-- 
2.34.1





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux