WKUP_PADCONFIG registers for wkup_uart0 and mcu_uart0 lies
under wkup_pmx2 for J7200. Thus, modify pinmux for both
of them.
Signed-off-by: Bhavya Kapoor <b-kapoor@xxxxxx>
---
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 17 +++++++++--------
1 file changed, 9 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 1d8bddcae90e..160580a0584a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -119,24 +119,25 @@ transceiver3: can-phy3 {
};
&wkup_pmx0 {
+};
+
+&wkup_pmx2 {
mcu_uart0_pins_default: mcu-uart0-default-pins {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
- J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
- J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */
- J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
+ J721E_WKUP_IOPAD(0x90, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */
+ J721E_WKUP_IOPAD(0x94, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
+ J721E_WKUP_IOPAD(0x8c, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
+ J721E_WKUP_IOPAD(0x88, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
>;
};
wkup_uart0_pins_default: wkup-uart0-default-pins {
pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
- J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
+ J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
+ J721E_WKUP_IOPAD(0x4c, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
>;
};
-};
-&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
--
2.34.1
