The LED implementation of qca808x and qca807x is the same but qca807x supports also Fiber port and have different hw control bits for Fiber port. In preparation for qca807x introduction, move all the common define to shared header. Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx> --- drivers/net/phy/qcom/qca808x.c | 65 ---------------------------------- drivers/net/phy/qcom/qcom.h | 65 ++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+), 65 deletions(-) diff --git a/drivers/net/phy/qcom/qca808x.c b/drivers/net/phy/qcom/qca808x.c index 8377325f157e..f1edff6b6bfc 100644 --- a/drivers/net/phy/qcom/qca808x.c +++ b/drivers/net/phy/qcom/qca808x.c @@ -62,29 +62,6 @@ #define QCA808X_DBG_AN_TEST 0xb #define QCA808X_HIBERNATION_EN BIT(15) -#define QCA808X_MMD7_LED_GLOBAL 0x8073 -#define QCA808X_LED_BLINK_1 GENMASK(11, 6) -#define QCA808X_LED_BLINK_2 GENMASK(5, 0) -/* Values are the same for both BLINK_1 and BLINK_2 */ -#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3) -#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0) -#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1) -#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2) -#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3) -#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4) -#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5) -#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6) -#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7) -#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0) -#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0) -#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1) -#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2) -#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3) -#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4) -#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5) -#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6) -#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7) - #define QCA808X_MMD7_LED2_CTRL 0x8074 #define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075 #define QCA808X_MMD7_LED1_CTRL 0x8076 @@ -92,51 +69,9 @@ #define QCA808X_MMD7_LED0_CTRL 0x8078 #define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2)) -/* LED hw control pattern is the same for every LED */ -#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0) -#define QCA808X_LED_SPEED2500_ON BIT(15) -#define QCA808X_LED_SPEED2500_BLINK BIT(14) -/* Follow blink trigger even if duplex or speed condition doesn't match */ -#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13) -#define QCA808X_LED_FULL_DUPLEX_ON BIT(12) -#define QCA808X_LED_HALF_DUPLEX_ON BIT(11) -#define QCA808X_LED_TX_BLINK BIT(10) -#define QCA808X_LED_RX_BLINK BIT(9) -#define QCA808X_LED_TX_ON_10MS BIT(8) -#define QCA808X_LED_RX_ON_10MS BIT(7) -#define QCA808X_LED_SPEED1000_ON BIT(6) -#define QCA808X_LED_SPEED100_ON BIT(5) -#define QCA808X_LED_SPEED10_ON BIT(4) -#define QCA808X_LED_COLLISION_BLINK BIT(3) -#define QCA808X_LED_SPEED1000_BLINK BIT(2) -#define QCA808X_LED_SPEED100_BLINK BIT(1) -#define QCA808X_LED_SPEED10_BLINK BIT(0) - #define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079 #define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2)) -/* LED force ctrl is the same for every LED - * No documentation exist for this, not even internal one - * with NDA as QCOM gives only info about configuring - * hw control pattern rules and doesn't indicate any way - * to force the LED to specific mode. - * These define comes from reverse and testing and maybe - * lack of some info or some info are not entirely correct. - * For the basic LED control and hw control these finding - * are enough to support LED control in all the required APIs. - * - * On doing some comparison with implementation with qca807x, - * it was found that it's 1:1 equal to it and confirms all the - * reverse done. It was also found further specification with the - * force mode and the blink modes. - */ -#define QCA808X_LED_FORCE_EN BIT(15) -#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13) -#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3) -#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2) -#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1) -#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0) - #define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a /* QSDK sets by default 0x46 to this reg that sets BIT 6 for * LED to active high. It's not clear what BIT 3 and BIT 4 does. diff --git a/drivers/net/phy/qcom/qcom.h b/drivers/net/phy/qcom/qcom.h index dc259bbf0678..9e24997c355f 100644 --- a/drivers/net/phy/qcom/qcom.h +++ b/drivers/net/phy/qcom/qcom.h @@ -103,6 +103,71 @@ /* Added for reference of existence but should be handled by wait_for_completion already */ #define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3)) +#define QCA808X_MMD7_LED_GLOBAL 0x8073 +#define QCA808X_LED_BLINK_1 GENMASK(11, 6) +#define QCA808X_LED_BLINK_2 GENMASK(5, 0) +/* Values are the same for both BLINK_1 and BLINK_2 */ +#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3) +#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0) +#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1) +#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2) +#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3) +#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4) +#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5) +#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6) +#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7) +#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0) +#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0) +#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1) +#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2) +#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3) +#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4) +#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5) +#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6) +#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7) + +/* LED hw control pattern is the same for every LED */ +#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0) +#define QCA808X_LED_SPEED2500_ON BIT(15) +#define QCA808X_LED_SPEED2500_BLINK BIT(14) +/* Follow blink trigger even if duplex or speed condition doesn't match */ +#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13) +#define QCA808X_LED_FULL_DUPLEX_ON BIT(12) +#define QCA808X_LED_HALF_DUPLEX_ON BIT(11) +#define QCA808X_LED_TX_BLINK BIT(10) +#define QCA808X_LED_RX_BLINK BIT(9) +#define QCA808X_LED_TX_ON_10MS BIT(8) +#define QCA808X_LED_RX_ON_10MS BIT(7) +#define QCA808X_LED_SPEED1000_ON BIT(6) +#define QCA808X_LED_SPEED100_ON BIT(5) +#define QCA808X_LED_SPEED10_ON BIT(4) +#define QCA808X_LED_COLLISION_BLINK BIT(3) +#define QCA808X_LED_SPEED1000_BLINK BIT(2) +#define QCA808X_LED_SPEED100_BLINK BIT(1) +#define QCA808X_LED_SPEED10_BLINK BIT(0) + +/* LED force ctrl is the same for every LED + * No documentation exist for this, not even internal one + * with NDA as QCOM gives only info about configuring + * hw control pattern rules and doesn't indicate any way + * to force the LED to specific mode. + * These define comes from reverse and testing and maybe + * lack of some info or some info are not entirely correct. + * For the basic LED control and hw control these finding + * are enough to support LED control in all the required APIs. + * + * On doing some comparison with implementation with qca807x, + * it was found that it's 1:1 equal to it and confirms all the + * reverse done. It was also found further specification with the + * force mode and the blink modes. + */ +#define QCA808X_LED_FORCE_EN BIT(15) +#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13) +#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3) +#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2) +#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1) +#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0) + #define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C #define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B #define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A -- 2.43.0
