Hi Sakari On Thu, Dec 07, 2023 at 09:57:06AM +0000, Sakari Ailus wrote: > Hi Jacopo, > > On Wed, Dec 06, 2023 at 04:58:59PM +0100, Jacopo Mondi wrote: > > Add bindings for OmniVision OV64A40. > > > > Co-developed-by: Lee Jackson <lee.jackson@xxxxxxxxxxx> > > Signed-off-by: Jacopo Mondi <jacopo.mondi@xxxxxxxxxxxxxxxx> > > Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx> > > --- > > .../bindings/media/i2c/ovti,ov64a40.yaml | 97 +++++++++++++++++++ > > 1 file changed, 97 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > new file mode 100644 > > index 000000000000..e6c9d540a2dd > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > @@ -0,0 +1,97 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov64a40.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: OmniVision OV64A40 Image Sensor > > + > > +maintainers: > > + - Jacopo Mondi <jacopo.mondi@xxxxxxxxxxxxxxxx> > > + > > +allOf: > > + - $ref: /schemas/media/video-interface-devices.yaml# > > + > > +properties: > > + compatible: > > + const: ovti,ov64a40 > > + > > + reg: > > + maxItems: 1 > > + > > + clocks: > > + maxItems: 1 > > + > > + avdd-supply: > > + description: Analog voltage supply, 2.8 volts > > + > > + dvdd-supply: > > + description: Digital core voltage supply, 1.1 volts > > + > > + dovdd-supply: > > + description: Digital I/O voltage supply, 1.8 volts > > + > > + powerdown-gpios: > > + maxItems: 1 > > + > > + reset-gpios: > > + maxItems: 1 > > + > > + port: > > + $ref: /schemas/graph.yaml#/$defs/port-base > > + additionalProperties: false > > + > > + properties: > > + endpoint: > > + $ref: /schemas/media/video-interfaces.yaml# > > + additionalProperties: false > > + > > + properties: > > + bus-type: > > + enum: > > + - 1 # MIPI CSI-2 C-PHY > > + - 4 # MIPI CSI-2 D-PHY > > + data-lanes: true > > + link-frequencies: true > > + clock-noncontinuous: true > > + remote-endpoint: true > > + > > +required: > > + - compatible > > + - reg > > + - clocks > > + - port > > + > > +unevaluatedProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + camera@36 { > > + compatible = "ovti,ov64a40"; > > + reg = <0x36>; > > + clocks = <&camera_clk>; > > + dovdd-supply = <&vgen4_reg>; > > + avdd-supply = <&vgen3_reg>; > > + dvdd-supply = <&vgen2_reg>; > > + powerdown-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; > > + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > > + rotation = <180>; > > + orientation = <2>; > > + > > + port { > > + endpoint { > > + remote-endpoint = <&mipi_csi2_in>; > > + bus-type = <4>; > > + data-lanes = <1 2 3 4>; > > This is missing link-frequencies. > I was not sure about this, in facts. Bindings are about HW while link-frequencies is only about restricting how the driver configures the sensor. Thus, I've not listed it as mandatory however the driver mandates its presence. Should I make it mandatory in bindings ? > > + }; > > + }; > > + }; > > + }; > > + > > +... > > -- > Regards, > > Sakari Ailus
