DW uMCTL2 DDRC ECC has a so called ECC Scrub feature in case if an
single-bit error is detected. The scrub is executed as a new RMW operation
to the location that resulted in a single-bit error thus fixing the ECC
code preserved in the SDRAM. But that feature not only optional, but also
runtime switchable. So there can be platforms with DW uMCTL2 DDRC not
supporting hardware-base scrub. In those cases the single-bit errors will
still be detected but won't be fixed until the next SDRAM write commands
to the erroneous location. Since the ECC Scrub feature availability is
detectable by means of the ECCCFG0.dis_scrub flag state use it to tune the
MCI core up so one would automatically execute the platform-specific
scrubbing to the affected SDRAM location. It's now possible to be done
since the DW uMCTL2 DDRC driver supports the actual system address
reported to the MCI core. The only thing left to do is to auto-detect the
ECC Scrub feature availability and set the mem_ctl.info.scrub_mode mode
with SCRUB_SW_SRC if the feature is unavailable. The rest will be done by
the MCI core when the single-bit errors happen.
Signed-off-by: Serge Semin <fancer.lancer@xxxxxxxxx>
---
drivers/edac/synopsys_edac.c | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)
diff --git a/drivers/edac/synopsys_edac.c b/drivers/edac/synopsys_edac.c
index 001553f3849a..4ee39d6809cc 100644
--- a/drivers/edac/synopsys_edac.c
+++ b/drivers/edac/synopsys_edac.c
@@ -32,6 +32,7 @@
#define SNPS_EDAC_MOD_VER "1"
/* DDR capabilities */
+#define SNPS_CAP_ECC_SCRUB BIT(0)
#define SNPS_CAP_ZYNQMP BIT(31)
/* Synopsys uMCTL2 DDR controller registers that are relevant to ECC */
@@ -119,6 +120,7 @@
#define DDR_MSTR_MEM_DDR2 0
/* ECC CFG0 register definitions */
+#define ECC_CFG0_DIS_SCRUB BIT(4)
#define ECC_CFG0_MODE_MASK GENMASK(2, 0)
/* ECC status register definitions */
@@ -1014,6 +1016,10 @@ static int snps_get_ddrc_info(struct snps_edac_priv *priv)
return -ENXIO;
}
+ /* Assume HW-src scrub is always available if it isn't disabled */
+ if (!(regval & ECC_CFG0_DIS_SCRUB))
+ priv->info.caps |= SNPS_CAP_ECC_SCRUB;
+
/* Auto-detect the basic HIF/SDRAM bus parameters */
regval = readl(priv->baseaddr + DDR_MSTR_OFST);
@@ -1490,8 +1496,14 @@ static struct mem_ctl_info *snps_mc_create(struct snps_edac_priv *priv)
MEM_FLAG_DDR3 | MEM_FLAG_LPDDR3 |
MEM_FLAG_DDR4 | MEM_FLAG_LPDDR4;
mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_SECDED;
- mci->scrub_cap = SCRUB_FLAG_HW_SRC;
- mci->scrub_mode = SCRUB_NONE;
+
+ if (priv->info.caps & SNPS_CAP_ECC_SCRUB) {
+ mci->scrub_mode = SCRUB_HW_SRC;
+ mci->scrub_cap = SCRUB_FLAG_HW_SRC;
+ } else {
+ mci->scrub_mode = SCRUB_SW_SRC;
+ mci->scrub_cap = SCRUB_FLAG_SW_SRC;
+ }
mci->edac_cap = EDAC_FLAG_SECDED;
mci->ctl_name = "snps_umctl2_ddrc";
@@ -1584,6 +1596,8 @@ static int snps_ddrc_info_show(struct seq_file *s, void *data)
seq_puts(s, "Caps:");
if (priv->info.caps) {
+ if (priv->info.caps & SNPS_CAP_ECC_SCRUB)
+ seq_puts(s, " +Scrub");
if (priv->info.caps & SNPS_CAP_ZYNQMP)
seq_puts(s, " +ZynqMP");
} else {
--
2.41.0
