From: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
Add support for MP2971 and MP2973, the successor of MP2975.
The major differences are:
- On MP2973 and MP2971 the Vref cannot be read and thus most of
the OVP/current calculations won't work.
- MP2973 and MP2971 also support LINEAR format for VOUT
- MP2973 and MP2971 do not support OVP2
- On MP2973 and MP2971 most registers are in LINEAR format
- The IMVP9_EN bit has a different position
- Per phase current sense haven't been implemented.
As on MP2975 most of the FAULT_LIMIT and WARN_LIMIT registers
have been redefined and doesn't provide the functionality as
defined in PMBUS spec.
Tested on MP2973 and MP2971.
Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx>
---
drivers/hwmon/pmbus/mp2975.c | 262 +++++++++++++++++++++++++++++------
1 file changed, 221 insertions(+), 41 deletions(-)
diff --git a/drivers/hwmon/pmbus/mp2975.c b/drivers/hwmon/pmbus/mp2975.c
index 13d8b95eb992..83242595ccbe 100644
--- a/drivers/hwmon/pmbus/mp2975.c
+++ b/drivers/hwmon/pmbus/mp2975.c
@@ -35,6 +35,8 @@
#define MP2975_MFR_OVP_TH_SET 0xe5
#define MP2975_MFR_UVP_SET 0xe6
+#define MP2973_MFR_RESO_SET 0xc7
+
#define MP2975_VOUT_FORMAT BIT(15)
#define MP2975_VID_STEP_SEL_R1 BIT(4)
#define MP2975_IMVP9_EN_R1 BIT(13)
@@ -49,8 +51,32 @@
#define MP2975_SENSE_AMPL_HALF 2
#define MP2975_VIN_UV_LIMIT_UNIT 8
+#define MP2973_VOUT_FORMAT_R1 GENMASK(7, 6)
+#define MP2973_VOUT_FORMAT_R2 GENMASK(4, 3)
+#define MP2973_VOUT_FORMAT_DIRECT_R1 BIT(7)
+#define MP2973_VOUT_FORMAT_LINEAR_R1 BIT(6)
+#define MP2973_VOUT_FORMAT_DIRECT_R2 BIT(4)
+#define MP2973_VOUT_FORMAT_LINEAR_R2 BIT(3)
+
+#define MP2973_MFR_VR_MULTI_CONFIG_R1 0x0d
+#define MP2973_MFR_VR_MULTI_CONFIG_R2 0x1d
+#define MP2973_VID_STEP_SEL_R1 BIT(4)
+#define MP2973_IMVP9_EN_R1 BIT(14)
+#define MP2973_VID_STEP_SEL_R2 BIT(3)
+#define MP2973_IMVP9_EN_R2 BIT(13)
+
+#define MP2973_MFR_READ_IOUT_PK 0x90
+#define MP2973_MFR_READ_POUT_PK 0x91
+
#define MP2975_MAX_PHASE_RAIL1 8
#define MP2975_MAX_PHASE_RAIL2 4
+
+#define MP2973_MAX_PHASE_RAIL1 14
+#define MP2973_MAX_PHASE_RAIL2 6
+
+#define MP2971_MAX_PHASE_RAIL1 8
+#define MP2971_MAX_PHASE_RAIL2 3
+
#define MP2975_PAGE_NUM 2
#define MP2975_RAIL2_FUNC (PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | \
@@ -58,11 +84,13 @@
PMBUS_HAVE_POUT | PMBUS_PHASE_VIRTUAL)
enum chips {
- mp2975
+ mp2971, mp2973, mp2975
};
static const int mp2975_max_phases[][MP2975_PAGE_NUM] = {
[mp2975] = { MP2975_MAX_PHASE_RAIL1, MP2975_MAX_PHASE_RAIL2 },
+ [mp2973] = { MP2973_MAX_PHASE_RAIL1, MP2973_MAX_PHASE_RAIL2 },
+ [mp2971] = { MP2971_MAX_PHASE_RAIL1, MP2971_MAX_PHASE_RAIL2 },
};
struct mp2975_data {
@@ -79,6 +107,8 @@ struct mp2975_data {
};
static const struct i2c_device_id mp2975_id[] = {
+ {"mp2971", mp2971},
+ {"mp2973", mp2973},
{"mp2975", mp2975},
{}
};
@@ -215,6 +245,76 @@ mp2975_read_phases(struct i2c_client *client, struct mp2975_data *data,
return ret;
}
+static int mp2973_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp2975_data *data = to_mp2975_data(info);
+ int ret;
+
+ switch (reg) {
+ case PMBUS_OT_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(7, 0));
+ break;
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(7, 0));
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST(ret, MP2975_VIN_UV_LIMIT_UNIT);
+ break;
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ /*
+ * MP2971 and mp2973 only supports tracking (ovp1) mode.
+ */
+ ret = mp2975_read_word_helper(client, page, phase,
+ MP2975_MFR_OVP_TH_SET,
+ GENMASK(2, 0));
+ if (ret < 0)
+ return ret;
+
+ ret = data->vout_max[page] + 50 * (ret + 1);
+ break;
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(8, 0));
+ if (ret < 0)
+ return ret;
+ ret = mp2975_vid2direct(info->vrm_version[page], ret);
+ break;
+ case PMBUS_VIRT_READ_POUT_MAX:
+ ret = pmbus_read_word_data(client, page, phase,
+ MP2973_MFR_READ_POUT_PK);
+ break;
+ case PMBUS_VIRT_READ_IOUT_MAX:
+ ret = pmbus_read_word_data(client, page, phase,
+ MP2973_MFR_READ_IOUT_PK);
+ break;
+ case PMBUS_UT_WARN_LIMIT:
+ case PMBUS_UT_FAULT_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_WARN_LIMIT:
+ case PMBUS_VOUT_OV_WARN_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_IIN_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_UC_FAULT_LIMIT:
+ case PMBUS_POUT_OP_FAULT_LIMIT:
+ case PMBUS_POUT_OP_WARN_LIMIT:
+ case PMBUS_PIN_OP_WARN_LIMIT:
+ return -ENXIO;
+ default:
+ return -ENODATA;
+ }
+
+ return ret;
+}
+
static int mp2975_read_word_data(struct i2c_client *client, int page,
int phase, int reg)
{
@@ -386,7 +486,7 @@ mp2975_identify_multiphase(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_identify_vid(struct i2c_client *client, struct mp2975_data *data,
+mp297x_identify_vid(struct i2c_client *client, struct mp2975_data *data,
struct pmbus_driver_info *info, u32 reg, int page,
u32 imvp_bit, u32 vr_bit)
{
@@ -422,7 +522,7 @@ mp2975_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
return ret;
/* Identify VID mode for rail 1. */
- ret = mp2975_identify_vid(client, data, info,
+ ret = mp297x_identify_vid(client, data, info,
MP2975_MFR_VR_MULTI_CONFIG_R1, 0,
MP2975_IMVP9_EN_R1, MP2975_VID_STEP_SEL_R1);
if (ret < 0)
@@ -430,10 +530,39 @@ mp2975_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
/* Identify VID mode for rail 2, if connected. */
if (info->phases[1])
- ret = mp2975_identify_vid(client, data, info,
+ ret = mp297x_identify_vid(client, data, info,
MP2975_MFR_VR_MULTI_CONFIG_R2, 1,
MP2975_IMVP9_EN_R2,
MP2975_VID_STEP_SEL_R2);
+
+ return ret;
+}
+
+static int
+mp2973_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
+ struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 1. */
+ ret = mp297x_identify_vid(client, data, info,
+ MP2973_MFR_VR_MULTI_CONFIG_R1, 0,
+ MP2973_IMVP9_EN_R1, MP2973_VID_STEP_SEL_R1);
+
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 2, if connected. */
+ if (info->phases[1])
+ ret = mp297x_identify_vid(client, data, info,
+ MP2973_MFR_VR_MULTI_CONFIG_R2, 1,
+ MP2973_IMVP9_EN_R2,
+ MP2973_VID_STEP_SEL_R2);
+
return ret;
}
@@ -532,7 +661,7 @@ mp2975_vref_offset_get(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
+mp297x_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
struct pmbus_driver_info *info, int page)
{
int ret;
@@ -548,17 +677,33 @@ mp2975_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_set_vout_format(struct i2c_client *client,
+mp297x_set_vout_format(struct i2c_client *client,
struct mp2975_data *data, int page)
{
int ret;
- ret = i2c_smbus_read_word_data(client, MP2975_MFR_DC_LOOP_CTRL);
- if (ret < 0)
- return ret;
/* Enable DIRECT VOUT format 1mV/LSB */
- ret &= ~MP2975_VOUT_FORMAT;
- ret = i2c_smbus_write_word_data(client, MP2975_MFR_DC_LOOP_CTRL, ret);
+ if (data->chip_id == mp2975) {
+ ret = i2c_smbus_read_word_data(client, MP2975_MFR_DC_LOOP_CTRL);
+ if (ret < 0)
+ return ret;
+ ret &= ~MP2975_VOUT_FORMAT;
+ ret = i2c_smbus_write_word_data(client, MP2975_MFR_DC_LOOP_CTRL, ret);
+ } else {
+ ret = i2c_smbus_read_word_data(client, MP2973_MFR_RESO_SET);
+ if (ret < 0)
+ return ret;
+
+ if (page == 0) {
+ ret &= ~MP2973_VOUT_FORMAT_R1;
+ ret |= MP2973_VOUT_FORMAT_DIRECT_R1;
+ } else {
+ ret &= ~MP2973_VOUT_FORMAT_R2;
+ ret |= MP2973_VOUT_FORMAT_DIRECT_R2;
+ }
+
+ ret = i2c_smbus_write_word_data(client, MP2973_MFR_RESO_SET, ret);
+ }
return ret;
}
@@ -605,24 +750,28 @@ mp2975_vout_per_rail_config_get(struct i2c_client *client,
for (i = 0; i < data->info.pages; i++) {
ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, i);
if (ret < 0)
- return ret;
+ continue;
- /* Obtain voltage reference offsets. */
- ret = mp2975_vref_offset_get(client, data, i);
+ /*
+ * Set VOUT format for READ_VOUT command : direct.
+ * Pages on same device can be configured with different
+ * formats.
+ */
+ ret = mp297x_set_vout_format(client, data, i);
if (ret < 0)
return ret;
/* Obtain maximum voltage values. */
- ret = mp2975_vout_max_get(client, data, info, i);
+ ret = mp297x_vout_max_get(client, data, info, i);
if (ret < 0)
return ret;
- /*
- * Set VOUT format for READ_VOUT command : direct.
- * Pages on same device can be configured with different
- * formats.
- */
- ret = mp2975_set_vout_format(client, data, i);
+ /* Skip if reading Vref is unsupported */
+ if (data->chip_id != mp2975)
+ continue;
+
+ /* Obtain voltage reference offsets. */
+ ret = mp2975_vref_offset_get(client, data, i);
if (ret < 0)
return ret;
@@ -660,6 +809,23 @@ static struct pmbus_driver_info mp2975_info = {
.read_word_data = mp2975_read_word_data,
};
+static struct pmbus_driver_info mp2973_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .m[PSC_VOLTAGE_OUT] = 1,
+ .R[PSC_VOLTAGE_OUT] = 3,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_POUT |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT,
+ .read_word_data = mp2973_read_word_data,
+};
+
static int mp2975_probe(struct i2c_client *client)
{
struct pmbus_driver_info *info;
@@ -679,6 +845,11 @@ static int mp2975_probe(struct i2c_client *client)
memcpy(data->max_phases, mp2975_max_phases[data->chip_id],
sizeof(data->max_phases));
+ if (data->chip_id == mp2975)
+ memcpy(&data->info, &mp2975_info, sizeof(*info));
+ else
+ memcpy(&data->info, &mp2973_info, sizeof(*info));
+
info = &data->info;
/* Identify multiphase configuration for rail 2. */
@@ -693,30 +864,37 @@ static int mp2975_probe(struct i2c_client *client)
data->info.func[1] = MP2975_RAIL2_FUNC;
}
- /* Identify multiphase configuration. */
- ret = mp2975_identify_multiphase(client, data, info);
- if (ret)
- return ret;
+ if (data->chip_id == mp2975) {
+ /* Identify multiphase configuration. */
+ ret = mp2975_identify_multiphase(client, data, info);
+ if (ret)
+ return ret;
- /* Identify VID setting per rail. */
- ret = mp2975_identify_rails_vid(client, data, info);
- if (ret < 0)
- return ret;
+ /* Identify VID setting per rail. */
+ ret = mp2975_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
- /* Obtain current sense gain of power stage. */
- ret = mp2975_current_sense_gain_get(client, data);
- if (ret)
- return ret;
+ /* Obtain current sense gain of power stage. */
+ ret = mp2975_current_sense_gain_get(client, data);
+ if (ret)
+ return ret;
- /* Obtain voltage reference values. */
- ret = mp2975_vref_get(client, data, info);
- if (ret)
- return ret;
+ /* Obtain voltage reference values. */
+ ret = mp2975_vref_get(client, data, info);
+ if (ret)
+ return ret;
- /* Obtain vout over-voltage scales. */
- ret = mp2975_vout_ov_scale_get(client, data, info);
- if (ret < 0)
- return ret;
+ /* Obtain vout over-voltage scales. */
+ ret = mp2975_vout_ov_scale_get(client, data, info);
+ if (ret < 0)
+ return ret;
+ } else {
+ /* Identify VID setting per rail. */
+ ret = mp2973_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
+ }
/* Obtain offsets, maximum and format for vout. */
ret = mp2975_vout_per_rail_config_get(client, data, info);
@@ -727,6 +905,8 @@ static int mp2975_probe(struct i2c_client *client)
}
static const struct of_device_id __maybe_unused mp2975_of_match[] = {
+ {.compatible = "mps,mp2971", .data = (void *)mp2971},
+ {.compatible = "mps,mp2973", .data = (void *)mp2973},
{.compatible = "mps,mp2975", .data = (void *)mp2975},
{}
};
--
2.41.0
